Epson LQ-1150 II User Manual Download Page 54 | Manualshive

Page: 54 / 129

background image

2-20

Using the Printer

6. Slide the left sprocket unit so that its sprockets match the

position of the holes in the paper and lock the unit in place.
Then slide the right sprocket unit to match the width of your
paper, but do not lock it. Move the paper support midway
between the two sprocket units.

7. Make sure your paper has a clean, straight leading edge. Open

the sprocket covers. Fit the first holes of the paper over the
sprocket pins and then close the sprocket covers. Slide the
right sprocket unit to remove any slack in the paper and then
lock it in place.

Note:

Remove any remaining slack by gently pulling the paper from the
rear or bottom.

«
...
52
53
54
55
56
...
»

Summary of Contents for LQ-1150 II


































































































































Reviews:

No comments

Related manuals for LQ-1150 II

Brand: Ier Pages: 8

Brand: Samsung Pages: 347

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 180

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 18

SCX-4521FG - B/W Laser - All-in-One

Brand: Samsung Pages: 215

SCX 6320F - B/W Laser - All-in-One

Brand: Samsung Pages: 332

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 248

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 253

ML 2851ND - B/W Laser Printer

Brand: Samsung Pages: 179

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 84

ML 1740 - B/W Laser Printer

Brand: Samsung Pages: 152

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 142

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 2

Brand: Samsung Pages: 384

Lazett Combo SCX-4216F

Brand: Samsung Pages: 135

Brand: Samsung Pages: 414

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands