EPS PSB 10000 4U, Operating Manual

Page: 2 / 110

© EPS Stromversorgung in 2022, this information is subject to change without notice 2 30000800_manual_psb_10000_4u_30kw_en_04
TABLE OF CONTENTS
1. General
1.1 About this document 5
1.1.1 Retention and use 5
1.1.2 Copyright 5
1.1.3 Validity 5
1.1.4 Symbols and warnings in this document 5
1.2 Warranty 5
1.3 Limitation of liability 5
1.4 Disposal of equipment 6
1.5 Product key 6
1.6 Intended usage 7
1.6.1 Symbols and warnings on the device 7
1.7 Safety 8
1.7.1 Safety notices 8
1.7.2 Responsibility of the operator 9
1.7.3 Requirements to the user 9
1.7.4 Responsibility of the user 9
1.7.5 Alarm signals 10
1.7.6 Functionality test 10
1.8 Technical Data 11
1.8.1 Approved operating conditions 11
1.8.2 General technical data 11
1.8.3 Specific technical data 12
1.8.4 Views 16
1.8.5 Control elements 21
1.9 Construction and function 22
1.9.1 General description 22
1.9.2 Block diagram 22
1.9.3 Scope of delivery 23
1.9.4 Accessories 23
1.9.5 Options 23
1.9.6 The control panel (HMI) 24
1.9.7 USB port (rear side) 27
1.9.8 Interface module slot 27
1.9.9 Analog interface 28
1.9.10 “Share BUS” connector 28
1.9.11 “Sense” connector (remote sensing) 28
1.9.12 Master-Slave bus 29
1.9.13 Ethernet port 29
1.9.14 Water cooling 29
2. Installation & commissioning
2.1 Transport and storage 30
2.1.1 Transport 30
2.1.2 Packaging 30
2.1.3 Storage 30
2.2 Unpacking and visual check 30
2.3 Installation 30
2.3.1 Safety procedures before installation and use 30
2.3.2 Preparation 30
2.3.3 Installing the device 32
2.3.4 Connection to water supply (WC models) 33
2.3.5 Connection to AC supply 35
2.3.6 Connection to DC loads or DC sources 37
2.3.7 Grounding of the DC terminal 38
2.3.8 Connection of remote sensing 39
2.3.9 Installation of an interface module 40
2.3.10 Connection of the analog interface 41
2.3.11 Connection of the Share bus 41
2.3.12 Connection of the USB port (rear side) 41
2.3.13 Initial commission 41
2.3.14 Commission after a firmware update or a long
period of non-use 41
3. Operation and application
3.1 Terms 42
3.2 Important notes 42
3.2.1 Personal safety 42
3.2.2 General 42
3.3 Operating modes 42
3.3.1 Voltage regulation / Constant voltage 42
3.3.2 Current regulation / constant current / current
limiting 43
3.3.3 Power regulation / constant power / power
limiting 44
3.3.4 Internal resistance regulation (source mode) 44
3.3.5 Resistance regulation / constant resistance
(sink mode) 45
3.3.6 Sink-source mode switching 45
3.3.7 Dynamic characteristics and stability criteria 45
3.4 Alarm conditions 46
3.4.1 Power Fail 46
3.4.2 Overtemperature 46
3.4.3 Overvoltage protection 46
3.4.4 Overcurrent protection 46
3.4.5 Overpower protection 46
3.4.6 Safety OVP 47
3.4.7 Share bus fail 47
3.5 Manual operation 48
3.5.1 Switching on the device 48
3.5.2 Switching the device off 48
3.5.3 Configuration via the menu 48
3.5.4 Adjustment limits 57
3.5.5 Changing the operating mode 57
3.5.6 Manual adjustment of set values 58