EPS PSB 10000 4U Operating Manual Download Page 92

Page: 92 / 110

30000800_manual_psb_10000_4u_30kw_en_04

3.11.15.8

Configuration step by step

Starting point

In menu

Function Generator

find the PV functions. Select here group

PV EN50530 (PS)

Step 1: Technology selection

The extended PV function requires to select the panel technology of

the solar panel which is going to be simulated. In case

cSI

Thin Film

don’t match your requirements or you are not sure about their technol-

ogy parameters, select

Manual

When selecting

Thin film

cSI

the configuration continues with

Step

Step 1-1: Adjust technology parameters

If technology

Manual

was selected in the previous screen, all dis-

played technology parameters can be adjusted by tapping on them

and entering the desired value. It’s recommended to adjust these val-

ues very carefully, because wrong settings can result in a PV curve

which doesn’t work as expected.
When resetting the device, these values are reset to defaults which are

the same as with technology

cSI

. Also see the overview in

3.11.15.3. It

means they don’t necessarily have to be adjusted. If any of the other

technologies was selected, this screen would be skipped and these

parameters set to the defined values.

Step 2: Input mode and solar panel base parameters

Selecting the input mode between

MPP

and

ULIK

determines what

pair of parameters has to be set in the configuration and also later in

the simulation. When setting pair Uoc/Isc, the other two pair is calcu-

lated with factors and automatically set.
The open circuit voltage (

Uoc

) and the short-circuit current (

Isc

) are

upper limits which are usually read from the data sheet of a solar panel

and entered here for the simulation. Two parameters each are con-

nected via the fill factors:

MPP

= U

× FFu / I

MPP

= I

× FFi

Step 3: Select simulation mode

For a description of the available simulation modes see

3.11.15.4.

When selecting

E/T

U/I

the configuration continues with

Step 4

otherwise an additional step is required

Summary of Contents for PSB 10000 4U















































































































Search results

Summary of Contents for PSB 10000 4U

Reviews:

Related manuals for PSB 10000 4U

Brands by name

Popular brands

EPS PSB 10000 4U, Operating Manual

Search results

Summary of Contents for PSB 10000 4U

Reviews:

Related manuals for PSB 10000 4U

Brands by name

Popular brands