EPS PSB 10000 4U Operating Manual Download Page 55

Page: 55 / 110

30000800_manual_psb_10000_4u_30kw_en_04

IF Settings

Description

ot E

t / M

P (

1 & 2 P

DHCP

The IF allows a DHCP server to allocate an IP address, a subnet mask and a gateway. If no DHCP

server is in the network then network parameters will be set as defined below.

IP address

This option is activated by default. An IP address can be manually allocated.

Subnet mask

Here a subnet mask can be defined if the default subnet mask is not suitable.

Gateway

Here a gateway address can be allocated if required..

DNS address

Here the addresses of the first and second Domain Name Servers (DNS) can be defined, if needed.

Port

Range: 0...65535, default port:

5025

= Modbus RTU

Reserved ports: 502, 537

Host name

User definable host name (default:

Client

)

Domain

User definable domain (default:

Workgroup

)

MAC address

of the internal Ethernet port

Speed / Duplex

Port 1

Manual selection of transmission speed (

10MBit

100MBit

) and duplex mode (

full

half

). It’s rec-

ommended to use the

Auto

option and only revert to another option if Auto fails.

Speed / Duplex

Port 2

Different Ethernet port settings for 2-port modules are possible, as these include an Ethernet

switch

Further communication related parameters

Group

Parameters & description

Timeouts

TCP keep-alive (internal) / TCP keep-alive (slot)

Activates/deactivates keep-alive network functionality for the internal Ethernet port and for an a

standard Ethernet module (IF-AB-ETHxx), if installed in the slot. The “keep-alive” network packets

are used to keep the socket connection open. As long as keep-alive is valid in the network, the

device will disable the Ethernet timeout. Also see below at

Timeout ETH

Timeout USB/RS232

Defines the max. time between two subsequent bytes or blocks of a transferred message. For

more information about the timeout refer to the external programming documentation “Program-

ming ModBus & SCPI”. Default value:

5 ms

, Range: 5...65535

Timeout ETH (internal) / Timeout ETH (slot)

Defines a timeout after which the device would close the socket connection if there was no com

mand communication between the controlling unit (PC, PLC etc.) and the device for the adjusted

time. The timeout is ineffective as long as option

TCP keep-alive

is enabled for the particular in-

terface and the keep-alive network service is running. A setting of 0 would deactivate the timeout

permanently. Default value:

5 s

, Range: 0 / 5...65535 (0 = timeout deactivated)

Interface monitoring / Timeout Interface monitoring

Activates/deactivates the interface monitoring (see section

“3.6.3.3. Interface monitoring”).

Default values: off,

5 s

/ Range: 5..65535

Protocols

Communication protocols

Enables or disables SCPI or ModBus communication protocols for the device. The change is im-

mediately effective. Only one of both can be disabled.

ModBus specification compliance

Allows to switch from

Limited

(default setting) to

Full

which makes the device send messages in

ModBus RTU or ModBus TCP format which fully comply to the specification and are compatible to

softwares available on the market. With

Limited

the device would still use the old, partially wrong

message format (see programming guide for details).

Summary of Contents for PSB 10000 4U















































































































Search results

Summary of Contents for PSB 10000 4U

Reviews:

Related manuals for PSB 10000 4U

Brands by name

Popular brands

EPS PSB 10000 4U, Operating Manual

Search results

Summary of Contents for PSB 10000 4U

Reviews:

Related manuals for PSB 10000 4U

Brands by name

Popular brands