EPS PSB 10000 4U Operating Manual Download Page 67

Page: 67 / 110

30000800_manual_psb_10000_4u_30kw_en_04

• Remote control has not been activated

In this mode of operation pin REM-SB can serve as lock, preventing the DC terminal from being switched on by any means.

This results in following possible situations:

terminal

Level on

pin REM-

Parameter

„REM-SB

Level“



Behavior

is off

HIGH

Normal



The DC terminal isn’t locked. It can be switched on by pushbutton “On/

Off” (front panel) or via command from digital interface.

LOW

Inverted

HIGH

Inverted



The DC terminal is locked. It can’t be switched on by pushbutton “On/

Off” (front panel) or via command from digital interface. When trying to

switch on, a pop-up in the display resp. an error message will be gener-

ated.

LOW

Normal

In case the DC terminal is already switched on, toggling the pin will switch the DC terminal off, similar to what it does in analog

remote control:

terminal

Level on

pin REM-

Parameter

„REM-SB

Level“



Behavior

is on

HIGH

Normal



The DC terminal remains on, nothing is locked. It can be switched on or

off by pushbutton or digital command.

LOW

Inverted

HIGH

Inverted



The DC terminal will be switched off and locked. Later it can be switched

on again by toggling the pin. During lock, pushbutton or digital command

can delete the request to switch on by pin.

LOW

Normal

b) Remote control of current and power

Requires remote control to be activated (pin REMOTE = LOW)
The set values PSEL and CSEL are generated from, for example, the

reference voltage VREF, using potentiometers for each. Hence the

power supply can selectively work in current limiting or power limiting

mode. According to the specification of max. 5 mA load for the VREF

output, potentiometers of at least 10 kΩ must be used.

The voltage set value VSEL is directly connected to VREF and will thus

be permanently 100%. This also means that the device can only work

in source mode.
If the control voltage is fed in from an external source it’s necessary

to consider the input voltage ranges for set values (0...5 V oder 0...10

V).

When using the voltage range 0...5 V the effective

resolution of set values and actual values halves.

Example with external

voltage source

Example with

potentiometers

c) Reading actual values

The AI provides the DC terminal values as current and voltage monitor. These can be read

using a standard multimeter or similar.

Summary of Contents for PSB 10000 4U















































































































Search results

Summary of Contents for PSB 10000 4U

Reviews:

Related manuals for PSB 10000 4U

Brands by name

Popular brands

EPS PSB 10000 4U, Operating Manual

Search results

Summary of Contents for PSB 10000 4U

Reviews:

Related manuals for PSB 10000 4U

Brands by name

Popular brands