Endress+Hauser Topcal S CPC310 Operating Instructions Manual Download Page 59

Page: 59 / 176

Commissioning

Contrast

Contrast setting where applicable
You can increase or reduce the contrast of the
display with the arrow keys

and

Date + time

Weekday
Day
Month
Year
Time

Enter the complete date and time here.
These data are used for the logbooks and the
automatic cleaning system.

Mode

Options
• pH
• Redox mV
• Redox %

Factory setting

Note!

• If you change the operating mode, all the

user settings are automatically reset. If you
want to save your settings, use a DAT
module.

• The Redox/ORP:% mode is not available for

redox sensors with Memosens technology
where the SW version is

≤

2.01.00.

Electrode type CH1

Options
• Glass el. 7.0
• Glass el. 4.6
• Antimony
• ISFET

Factory setting

Glass 7.0

Specify the sensor that is used (only pH).

Note!

• The type of electrode does not have to be

selected for digital sensors.

• The temperature sensor defaults to Pt 1000

when you change from a glass or antimony
electrode to ISFET. Pt 100 is selected when
the situation is the reverse.

• In the glass/ISFET version, Mycom S is

supplied for measuring with glass electrodes
as standard.

Connection type

Options
• Solution ground
• No solution ground

Factory setting

Solution ground

Specify whether you are measuring
symmetrically (=with PML) or unsymmetrically
(=without PML).

Note!

• This selection is not displayed for digital

sensors with Memosens technology. A
symmetrically high-resistance connection is
not required for digital data transmission.

• More information on symmetrical and

unsymmetrical measurement is provided on
the CD-ROM.

Temperature unit

Options
•

•

Factory setting

Temperature compensation,
temp.sensor input 1

Options
• ATC C1
• MTC
• MTC+Temp

Factory setting

ATC C1

Only for pH measurement:

ATC:

Automatic temperature compensation

using temperature sensor

MTC:

Temperature compensation with manual

input

MTC+temp:

Temperature compensation with

temperature entered manually. The
temperature measured with a temperature
sensor is displayed, however

Function

Options

Info

Hold

7. 00

Param

Edit

[+-]

[E]

Contrast

Hold

30
04
01

12:00

7. 00

Param

[¯ ]

[E]

Date+time

Weekday :
Day

Month

Year

Time

Select

7. 00

Hold

Param

Edit

[¯ ]

[E]

Sensor input

Redox/ORP mV
Redox/ORP %

Hold

7. 00

Param

Edit

Glas El. 7. 0

Glas El. 4.6
Antimon
ISFET

[¯]

[E]

pH electr.typeK1

Hold

Edit

7. 00

Param

[¯]

[E]

Sensor ground

solution ground

no solution ground

Hold

7. 00

Param

Edit

°C

°F

[¯]

[E]

Temp. unit

Hold

Next [E]

Param

Temp.comp. C2

ATC C1

MTC
MTC+Temp

Edit [¯]

pH 7.00

Summary of Contents for Topcal S CPC310

















































































































































































Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands

Endress+Hauser Topcal S CPC310, Operating Instructions Manual

Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands