Endress+Hauser Topcal S CPC310 Operating Instructions Manual Download Page 112

Page: 112 / 176

Commissioning

112

Simulation

Simulation of current outputs

Activation and subsequent
entry
• Simulation

– On
– Off

• Output 1

0.0 ... 22.0 mA

• Output 2

0.0 ... 22.0 mA

Factory setting

Simulation: Off
Output 1: 0.0 mA
Output 2: 0.0 mA

Adjust the simulation of the current outputs.

Simulation off:

The frozen values of the last

measurement are used for simulation.

Simulation on:

The current values for the

outputs can be altered for the simulation
(output 1, output 2).

Simulation of measured value,
temperature

Activation and subsequent
entry
• Simulation

– On
– Off

• pH/mV 1

-2.00 ... 16.00 pH

• Temperature

-50 ... +150

Factory setting

Simulation: Off
pH/mV 1: 7.00 pH
Temperature: 25.0

Adjust the simulation of measured values and
the temperature.

Simulation off:

The frozen values of the last

measurement are used for simulation.

Simulation on:

The values can be changed for

the simulation.

Simulation of relays

Activation and subsequent
entry
• Simulation

– On
– Off

• Alarm relay

– On
– Off

• Relay 1

– On
– Off

• Relay 2

– On
– Off

Factory setting

Simulation: Off
Alarm relay: Off
Relay 1/2: Off

Adjust the simulation of the relays.

Simulation off:

The last states are frozen and

used for simulation.

Simulation on:

The relays can be opened (on)

or closed (off).

Note!

If you return to the measurement mode with
the simulation switched on, "Simul" and "Hold"
flash in the display.

Instrument check

Select test

Options
• Display
• Keypad
• RAM
• EEPROM
• Flash

You can check the function of the transmitter
with the instrument check.

Display:

All the fields of the display are

addressed alternately. In this way, any defective
cells are visible.

Key pad:

The keys all have to be pressed one

after the other. If the system is functioning
perfectly, the appropriate symbols appear in the
display.

RAM:

"RAM o.k." message if operating

correctly without error.

EEPROM:

"EEPROM o.k." message if

operating correctly without error.

Flash

(memory): "Flash o.k." message if

operating correctly without error.

Function

Options

Info

Summary of Contents for Topcal S CPC310

















































































































































































Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands

Endress+Hauser Topcal S CPC310, Operating Instructions Manual

Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands