Endress+Hauser Topcal S CPC310 Operating Instructions Manual Download Page 69

Page: 69 / 176

Commissioning

Temperature compensation menu

To call the menu, select:
"

> Specialist > Set up 1 > Temperature"

Function

Options

Info

Temperature measurement

Options
• Off
• On

Factory setting

Only available with redox measurement

Select temperature compensation

Options
• Temp. comp. sensor
• Temp. comp. process (only for

pH operating mode)

Factory setting

Temperature

Only available with pH measurement
Select the temperature compensation
necessary.

Temperature compensation sensor:

Automatic (ATC) or manual (MTC)
temperature compensation

Temperature compensation process:

Compensation of the medium temperature
using customer-specific tables (see below)

Temperature

Temperature compensation

Options
• ATC C1
• MTC
• MTC+Temp

Factory setting

ATC C1

Only for pH measurement:

ATC:

Automatic temperature compensation

using temperature sensor

MTC:

Temperature compensation with manual

input

MTC+temp:

Temperature compensation with

temperature entered manually. The
temperature measured with a temperature
sensor is displayed, however

Note!

The type of temperature compensation selected
here is active during measuring operation. For
the calibration, you must configure the desired
compensation in the "Calibration" menu.

MTC temperature

-20.0 ... 150.0

Factory setting

25.0

Only available with pH and MTC or
MTC+Temp selected in the previous field.

Temperature sensor

Options
• Pt100
• Pt1000
• NTC 30K

Factory setting

Pt100

Select the temperature sensor to suit your
sensor

Temperature actual value

-5.00 ... +5.00

Factory setting

0.00

You can change/adjust the value currently
measured with the temperature sensor. The
temperature difference is stored internally as an
offset value.

Offset value

-5.0 ... +5.0

You can edit or reset the offset value resulting
from the previous field here.

Temperature compensation process

Select compensation

Options
• Select temp. table
• Edit table
• Reference temperature

Factory setting

Select temp. table

Select temp. table

You activate an existing

table.

Create table:

You create a specific table to suit

your requirements.

Reference temperature:

You enter a

temperature to which your measured values
refer.

Hold

mV -

114

Param

Edit

[¯]

[E]

Temp.meas1

off

Hold

7. 00

[E]

Select

Edit[¯]

Param

Temp. comp. sensor

Temp. comp. process

Summary of Contents for Topcal S CPC310

















































































































































































Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands

Endress+Hauser Topcal S CPC310, Operating Instructions Manual

Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands