Endress+Hauser Topcal S CPC310 Operating Instructions Manual Download Page 3

Page: 3 / 176

Table of contents

Safety instructions . . . . . . . . . . . . . . . . 5

1.1

Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2

Installation, commissioning and operation . . . . . . . . 5

1.3

Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4

Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.5

Notes on safety conventions and icons . . . . . . . . . . . 6

Identification . . . . . . . . . . . . . . . . . . . . 7

2.1

Device designation   . . . . . . . . . . . . . . . . . . . . . . . . .  7
2.1.1  Nameplate   . . . . . . . . . . . . . . . . . . . . . . . . .  7
2.1.2  Scope of delivery  . . . . . . . . . . . . . . . . . . . . .  7
2.1.3  Product structure   . . . . . . . . . . . . . . . . . . . .  8

2.2

Certificates and approvals . . . . . . . . . . . . . . . . . . . . 9

Installation . . . . . . . . . . . . . . . . . . . . . 10

3.1

System setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2

Incoming acceptance, transport, storage . . . . . . . . . 11

3.3

Installation conditions  . . . . . . . . . . . . . . . . . . . . . .  11
3.3.1  Types of mounting . . . . . . . . . . . . . . . . . . .  11
3.3.2  Spacing  . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
3.3.3  Assembly installation  . . . . . . . . . . . . . . . . .  12
3.3.4  Dimensions  . . . . . . . . . . . . . . . . . . . . . . . .  13

3.4

Installation instructions . . . . . . . . . . . . . . . . . . . . . 14
3.4.1 Securing

rinsing

block

to assembly . . . . . . . 14

3.4.2  Installation instructions . . . . . . . . . . . . . . .  14
3.4.3  Wall mounting   . . . . . . . . . . . . . . . . . . . . .  15
3.4.4  Post mounting and panel mounting  . . . . . .  16

3.5

Post-installation check . . . . . . . . . . . . . . . . . . . . . . 18

Wiring . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1

Electrical connection  . . . . . . . . . . . . . . . . . . . . . . .  19
4.1.1  Overview   . . . . . . . . . . . . . . . . . . . . . . . . .  19
4.1.2  Connection compartment sticker for

CPG310 control unit . . . . . . . . . . . . . . . . . 21

4.1.3 Connection compartment sticker,

Mycom S CPM153 . . . . . . . . . . . . . . . . . . 22

4.1.4 Power supply and communication connection

between transmitter and control unit . . . . . 23

4.1.5 Level probes for buffer and cleaner . . . . . . 24
4.1.6 Analog sensors . . . . . . . . . . . . . . . . . . . . . 25
4.1.7 Digital

sensors

with

Memosens technology . . . . . . . . . . . . . . . . 30

4.1.8  Current outputs . . . . . . . . . . . . . . . . . . . . .  32
4.1.9  Mycom relays  . . . . . . . . . . . . . . . . . . . . . .  35
4.1.10  External inputs (PLC to CPG310 ) and

outputs (CPG310 to PLC) . . . . . . . . . . . . . 36

4.1.11 External inputs (PLC to Mycom) . . . . . . . . 37
4.1.12 Inductive limit position switch . . . . . . . . . . 38

4.2

Post-connection check . . . . . . . . . . . . . . . . . . . . . . 40

Medium connection. . . . . . . . . . . . . . . 41

5.1

Compressed air pipe and additional valves . . . . . . . 41

5.2

Water pipe and rinse chamber . . . . . . . . . . . . . . . . 42

5.3

Multihoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.3.1 Connecting multihoses . . . . . . . . . . . . . . . 44

5.4

Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.4.1 Cleanfit CPA471/472/475 . . . . . . . . . . . . 45
5.4.2 Cleanfit CPA473/474 . . . . . . . . . . . . . . . . 47

5.5

Pumps  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.5.1  Compressed air control   . . . . . . . . . . . . . . . 49
5.5.2  Buffer and cleaner  . . . . . . . . . . . . . . . . . . . 50
5.5.3  Venting  . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.6

Post-connection check . . . . . . . . . . . . . . . . . . . . . . 51

Operation . . . . . . . . . . . . . . . . . . . . . . 52

6.1

Display and operating elements   . . . . . . . . . . . . . . . 52
6.1.1  Display   . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.1.2  Function of keys   . . . . . . . . . . . . . . . . . . . . 52
6.1.3  Service switch  . . . . . . . . . . . . . . . . . . . . . .  53
6.1.4  Measured value display  . . . . . . . . . . . . . . . 54
6.1.5  Operation access authorization . . . . . . . . . . 54
6.1.6  Menu editor types  . . . . . . . . . . . . . . . . . . . 55

6.2

Operation via FieldCare . . . . . . . . . . . . . . . . . . . . . 56

Commissioning . . . . . . . . . . . . . . . . . . 57

7.1

Points to note when commissioning
digital sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

7.2

Points to note when commissioning
ISFET sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

7.3

Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

7.4

Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

7.5

Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.5.1 Configuring Clean program . . . . . . . . . . . . 61

7.6

Summary of Contents for Topcal S CPC310

















































































































































































Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands

Endress+Hauser Topcal S CPC310, Operating Instructions Manual

Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands