manualshive.com logo in svg

Endress+Hauser Analytik Jena CyBio FeliX, Operating Instructions Manual, Page: 86 / 116

Share
Download
Endress+Hauser Analytik Jena CyBio FeliX Operating Instructions Manual Download Page 86

72

Rev. B  2022/02

 

CyBio FeliX

7.12 Troubleshooting - Instructions

7.12.1 Changing the device fuse

Fig. 45:

Fuses (2x) in the combination element at the rear of the device

Changing the device fuse

Device fuse has been changed.

WARNING

Danger due to electrical voltage!

Always unplug the power cord from the power outlet before changing the fuse. Check 

that there is no voltage on the device.

Name

Type/Value

1

Mains fuse 

T 4 A, 250V AC, 5x20 mm

1 High Breaking Capacity Fuse (Details 

→ 

 

„Overview operating data/conditions” on page 9

)

1.

Switch off the device.

2.

Unplug the power cord from the device and the power outlet.

3.

Pull the fuse holder out of the combination element using a small screwdriver (

→

 

 

see Fig. 45

).

4.

Check which fuse is defective.

5.

Remove the defective fuse from the fuse holder.

6.

Place the replacement fuse in the fuse holder.

7.

Reinsert the fuse holder.

8.

Switch on the device.

Summary of Contents for Analytik Jena CyBio FeliX





















































































































Reviews:

No comments