Endress+Hauser Analytik Jena CyBio FeliX Operating Instructions Manual Download Page 79

Page: 79 / 116

Rev. B 2022/02

CyBio FeliX

Operation

Compatibility between pipette tips

and LH adapters

Table 19: Compatibility overview

TIP

The specified usable volumes of the pipette tips may be limited by the software depend-

ing on the pipetting head used. This also applies to pipette tips with filters (filter tips),

where a small net volume may be available.

Tip type

Description

CyBio-TipRack 96/1000

1-/8-/12-channel CHOICE adapter; 10

l - 1000

CyBio-TipBox 96/250

1-/8-/12-channel CHOICE adapter; 10

l - 1000

1-/8-/12-channel adapter; Head R 96

CyBio-TipBox 96/50

8-/12-channel CHOICE adapter; 0.5

l - 50

1-/8-/12-channel adapter; Head R 96

CyBio-TipBox 192/60

1-/16-/24-channel CHOICE adapter; 0.5

l - 50

1-/16-/24-channel adapter; Head R 384

Summary of Contents for Analytik Jena CyBio FeliX





















































































































Search results

Summary of Contents for Analytik Jena CyBio FeliX

Reviews:

Endress+Hauser Analytik Jena CyBio FeliX, Operating Instructions Manual, Page: 79 / 116

Search results

Summary of Contents for Analytik Jena CyBio FeliX

Reviews: