background image

 

KOMET 200 - 600

 

10.2.2 

Input terminals 

Input Description 

Connection

Function 

BT 

n.o. contact 

1 pin 

Push button (serial 
switching) 

BTG 

n.o. contact 

1 pin 

Push button for pedestrian 
opening 

BA 

n.o. contact 

1 pin 

Push button OPEN 

BZ 

n.o. contact 

1 pin 

Push button CLOSE 

Ground - 

1 pin 

Mutual ground BT, BTG, BA 
and BZ 

BS 

n.c. contact 

1 pin 

Push button STOP 

Ground - 

1 pin 

Ground for STOP 

LSA 
LSI 

Each max. 6 photo-
cells with n.c. contact 
and terminating 
resistor 1k

 

2 pin 

Photo-cells for installation 
outside (LSA) and inside 
(LSI) 
(according to EN954-1 
category 2) 

Ground - 

1 pin 

Mutual ground LSA and LSI 

SLA 
SLZ 

Safety contact profile: 
resistor detection n.c. 
contact with 8.2k

 

resistor (serial or 
parallel with n.o. 
contact with 8.2 k

2 pin 

Integrated detectors with 
testing function (according 
to EN954-1 category 2) for 
safety contact profile for 
gate OPEN (SLA) and 
CLOSE (SLZ) 

Ground - 

1 pin 

Mutual ground SLA and SLZ

IMPg 

pulser 

See motor 

Pulser for pedestrian wing 

IMPf 

 

See motor 

Pulser for main wing 

SU 

 

Plug socket  Connection for timer module 

ASU2 

Funk  

Plug 

socket 

for receiver 
EKX1OF or 
receiver 
with 
decoder 

Integrated receiver for BT, 
BTG and MULTI 

Netz 
(L1, N 
and 
PE) 

3 pin 

Power supply 
230Vac – L1, N and PE 

Table7 

  

10.2.3 

Buttons on the controller 

Mark Function 

 

25

 

Summary of Contents for KOMET 200
















































Reviews: