background image

 

KOMET 200 - 600

 

 

Drawing 10 

  

1 Internal 

stops 

  

7.  Replace and refit the opener to the mounting support T. Now connect the 

opener/s to the terminals of the controller MO 36. Connect the main wing 
to the terminal 

FAHR

 and the pedestrian wing to the terminal 

GEH

. For 

one winged gates connect the wing to the terminal 

FAHR

8.  Connect to the mains. 

  

 

ATTENTION!

 During the next steps the gate wing will be moved electrically. 

Make sure the range of movement is free from obstacles. During learning the 
safety devices can react differently from the normal operation. 

  

9.  Press the button 

LERN

 on the controller for approx. 2 seconds. The 

display shows 

p1

.Press the button 

LERN

 again. The display now shows 

1f

10. Now select the number of gate wings. Push button 

BT

 until it displays 

2f

Confirm the displayed 

2f

 (for two wings) with the button 

LERN

. The 

display shows 

ha

 (manual operation). 

11. Now you can move each gate wing separately into the end positions in 

slow mode (dead man´s function). The main wing moves into direction 
OPEN only as long as button 

BT

 is pressed. When button 

BT

 is pushed 

again, the wing moves into direction CLOSED. The pedestrian wing moves 
into direction OPEN only as long as button 

BTG

 is pressed. When button 

BTG

 is pushed again, the wing moves into direction CLOSED. 

12. Now move the main wing with button 

BT

 into the end postitions OPEN and 

CLOSED. Now move the pedestrian wing with button 

BTG

 into the end 

positions OPEN and CLOSED. The internal end stops are now adjusted 
but not fixed. 

13. Move the gate wings with button 

BT

 and 

BTG

 into position „half OPEN“. 

  

 

ATTENTION!

 Do not give any further commands to the controller now. 

  

14. Remove the plug from the 5-pin connection 

FAHR

 and 

GEH

15. Loosen the screw at the mounting support T. Lift the narrow end of the 

gate opener out of the mounting support T. 

16. The three counter sunk screws from the internal stop 

must be tightened

 

by allen key. 

17. Replace and refit the opener to the mounting support T. 
18. Now connect the gate opener to the controller MO36. 

  

 

20

 

Summary of Contents for KOMET 200
















































Reviews: