Electrolux Professional Combi TOUCH 10 GN 1/1 User Manual Download Page 65

Page: 65 / 72

Anom-
aly

Type of
anomaly

Description

Possible causes

Actions

Htd

Stops
oven

Drain temperature
above safety limit

Possible lack of water in
the drain system.

• Check that the oven has water supply;
• Pour some fresh water on the bottom cavity

filter; pay attention, do not splash hot cavity
with cold water as it could damage the
machine.

• Wait for the alarm to blink off;
• If the problem persists, call Service.

InuS

Stops
oven

Inverter software ver-
sion (YODA board)
incompatible with
present UI SW
version

Wrong software upload
(example: after replacing
ACU board)

Inverter software version (YODA board) incom-
patible with present UI SW version.
Call service

LPIn

Stops
cycle

Boiler level sensor
problem

• Humid lime shortcutting

boiler level sensors.

• Insulation issues with

the boiler level sensors

The oven can continue to operate in convection
or in ISG mode.

• There is a problem with the water level in the

boiler: run a cleaning program including the
rinse and descale cycle and use 2 tabs C25
only. (Follow the procedure as per Operating
Manual);

• If the problem persists, call Service.

MCbM /
Fd13

Stops
oven

Lower inverter com-
munication problem

• Issue with the motor

inverter;

• Connection or electrical

issue.

Communication error with lower cavity motor
inverter.

• Try to switch the oven OFF/ON.
• If the problem persists, call Service.

MCtM /
FU13

Stops the
oven

Upper inverter com-
munication problem

• Issue with the motor

inverter;

• Connection or electrical

issue,

Communication error with upper cavity motor
inverter.

• Try to switch the oven OFF/ON.
• If the problem persists, call Service.

nIUS

Warning
Stops only
connectiv-
ity

NIU SW version is
incompatible with UI
SW version.

Once the NIU has been
installed, it has been rec-
ognized an incompatible
software version of the NIU

• Call service

nIUH

Warning
Stops only
connectiv-
ity

NIU unknown

nIUC

Warning
Stops only
connectiv-
ity

NIU configuration not
valid

nIUP

Warning
Stops only
connectiv-
ity

No valid PNC and SN
found

PCE1

Stops
oven

Wrong Parameter
configuration: Appli-
ance with boiler but
without lambda probe

Wrong Parameter configuration: Appliance with
boiler but without lambda probe.

PdEF

Stops
oven

Memorized default
parameters corrupted

Physical memory failure

Parameters memory corrupted;

• Try to switch the oven OFF/ON.
• If the problem persists, call service.

PFOr

One or more Factory
parameters are out of
range

One or more Factory
parameter are out of range

• Call service

PUOr

One or more User
parameters are out of
range

One or more User parame-
ters are out of range

• Call service

PUSr

The User parameters
calculated is different
to the stored one

Invalid data on User
parameters

• Call service

PFAC

Stops
oven

Factory parameters
map corrupted

Issue with the SW or with
the HW.

• Try to switch the oven OFF/ON.
• If the problem persists, call Service.

Summary of Contents for Combi TOUCH 10 GN 1/1









































































Search results

Summary of Contents for Combi TOUCH 10 GN 1/1

Reviews:

Related manuals for Combi TOUCH 10 GN 1/1

Brands by name

Popular brands

Electrolux Professional Combi TOUCH 10 GN 1/1, User Manual

Search results

Summary of Contents for Combi TOUCH 10 GN 1/1

Reviews:

Related manuals for Combi TOUCH 10 GN 1/1

Brands by name

Popular brands