Electrolux Professional Combi TOUCH 10 GN 1/1, User Manual

Page: 61 / 72

61
Anom-
aly
Type of
anomaly
Description
Possible causes Actions
CSOt Stops
cooking
cycle Cavity SSR NTC
overtemperature
(NTC3)
• Inlet air filter dirty;
• Cooling fan failure;
• Cooling inlet air sucking
warm/hot air;
• Oven installed by hot
machine;
• Steam/Heat leakage in
the electronic
compartment;
The oven can continue to work in recovery
mode: cooking cycles will not use the boiler.
• Do not switch the oven OFF;
• Wait for the temperature to decrease;
• Clean the inlet air filter;
• Check with a thin strip of paper whether a
consistent air flow can be detected at the
cooling air inlet: if not, call service;
• Check if the inlet cooling air may be affected
by heat produced in the kitchen (in case the
oven is located by hot appliances, stop
working with those appliances and inform
Service);
• If the error persists, call Service.
dESC Warning Descale Boiler Parameter bSCt has been
reached. Run a cleaning program including the rinse and
descale cycle and use 2 tabs C25 only for 6-10
grids models and 3 tabs only for 20 grids
models (follow the procedure as per Operating
Manual).
EbOL Stops
cycle/
preheating Boiler thermocouple
failure
• Connector failure;
• TC sensor failure;
• ACU failure.
The oven can continue to work without preheat-
ing (check the cooking results).
• Inform Service about the failure.
EbYP Warning Steam exhaust tem-
perature sensor
failure.
• Connector failure;
• TC sensor failure;
• ACU failure.
The oven can continue to work, it is possible
that water consumption increases.
Call Service.
ECEd Stops
cycle Bottom cavity thermo-
couple failure
• Connector failure;
• TC sensor failure;
• ACU failure.
The oven can continue to work only with 100 ℃
steam cycle.
Call Service.
ECEu Stops
cycle
Upper cavity thermo-
couple failure
• Connector failure;
• TC sensor failure;
• ACU failure.
The oven can continue to work only with 100 ℃
steam cycle.
Call Service.
ECLt Stops
oven Cleaning table not
present for the
MODEL and the
DETERGENT TYPE
in use Software missing Cleaning table not present for the MODEL and
the DETERGENT TYPE in use.
Call Service.
EGA0 Stops
oven No one valid GAS
table present in the
oven Software missing No one valid GAS table present in the oven.
Call Service.
EGAd Stops
oven Wrong GAS table
data Software missing Wrong GAS table data.
Call Service.
EGAt Stops
oven GAS table for this
appliance model not
found Software missing GAS table for this appliance model not found.
Call Service.
EH2O Stops
oven Water measured
inconsistent with
valves state
• Water supply valve
closed or partly closed;
• Temporary lack of water
supply pressure;
• Flow meter failure;
• Water system issue.
The oven can continue to work (check the
cooking results).
• Check if the water supply valve is open;
• Check the water pressure is > 1,5 bar;
• If the problem, persists call Service.
ELMb Stops
cooking
with steam
over 100
℃
Detected a problem
with the oxygen
sensor
• Lambda probe failure.
It is possible to continue using the oven in
Steam under 100
℃
• Cooking results in Steam mode may be
different from usual.
• Call Service in case cooking results are
persistently unsatisfactory.
EntC Stops
oven component compart-
ment NTC failure
(NTC1)
• Connector failure;
• TC sensor failure;
• ACU failure.
Electronic board temperature sensor damaged.
• Cooking impossible.
• Call Service.