Electrohome VistaGRAPHX 2500 User Manual Download | Manualshive

Page: 64 / 101

background image

MAINTENANCE

VistaGRAPHX 2500 User's Manual

4-6

WARNING

To reduce the danger from possible explosion,

always direct the surface of the lamp away from you.

Handle by the plastic housing only.

Insert the new lamp assembly
Hold the new lamp assembly with the labeled surface facing you (the two brass
nuts will be on the opposite side). Make sure that the glass lamp surface is on
your left — otherwise the unit will be upside down.

Figure 4.5. Lamp orientation

WARNING

Take care not to touch the exposed surface of the

lamp itself this could impair lamp performance

and shorten lamp life.

Grasp the lip of the lamp assembly and carefully align the lamp assembly with
the empty lamp area in the projector. Push straight into the lamp area, pushing
slowly but firmly to ensure that the housing is securely in place and is as far back
as possible.

Figure 4.6. Insert new lamp assembly

Replace the inner lamp door
Once the new lamp assembly is properly installed, shut and latch the inner door.

STEP 5

'

STEP 6

'

«
...
62
63
64
65
66
...
»

Summary of Contents for VistaGRAPHX 2500






































































































Reviews:

No comments

Related manuals for VistaGRAPHX 2500

Brand: FOREVER Pages: 48

Brand: Vankyo Pages: 39

Brand: paco Pages: 15

Brand: Costway Pages: 28

Brand: Optoma Pages: 93

Brand: RS Pages: 4

Brand: Barco Pages: 92

Brand: Akai Pages: 84

Brand: Optoma Pages: 73

Brand: Mitsubishi Pages: 79

ECO Spot PCE Series

Brand: Globus New Media Pages: 4

Brand: Kramer Pages: 4

Brand: Acer Pages: 56

Brand: Acer Pages: 63

Brand: Acer Pages: 57

Brand: Digital Projection Pages: 80

Notevision XG-C330X

Brand: Sharp Pages: 2

Notevision XG-P10XE

Brand: Sharp Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands