Electrohome VistaGRAPHX 2500 User Manual Download Page 13 | Manualshive

Page: 13 / 101

background image

INSTALLATION & SETUP

VistaGRAPHX 2500 User's Manual

2-10

Figure 2-9. VistaGRAPHX 2500 Back Panel

The RGB input (DAT 1) includes BNC type connectors for connection to a
variety of RGB sources. Such sources include VGA, SVGA, XGA, Mac,
PowerMac, DEC, Sun, SGI and others. VistaGRAPHX 2500 supports multiple
sync types: sync-on-green for data, composite, and separate H & V.

NOTES: 1)Depending on the source, you may need a custom adapter cable that
has BNC connectors at the projector end and different type of connector at the
other (such as a 15-pin "D" connector for computer sources). Contact your
dealer or Electrohome. 2)For best performance of HDTV sources, do not
connect to Dat1 — use the HDTV Input Module (option).

Connect the sync BNC input(s) first. Then connect the red, green and blue
source outputs to the RED, GREEN, and BLUE inputs on the panel. If the source
uses sync-on-green, only the red, green, and blue connections are required. If the
source provides a composite sync output, connect it to the H/C SYNC input. If
the source provides separate horizontal and vertical sync outputs, connect
horizontal sync to the H/C SYNC input and connect vertical sync to the V SYNC
input. See Figure 2-10.

Connect YUV (component) video as follows:

Y to "Green"
U (also called B-minus-Y) to "Blue"
V (also called R-minus-Y) to "Red"

NOTE: VistaGRAPHX 2500 does not automatically recognize a YUV signal.
When using YUV video, you must specify this signal type within the Image
Settings menu so that the projector can distinguish between this signal and other
RGB sources. See 3.6, Adjusting the Image.

RGB Input

'

«
...
11
12
13
14
15
...
»

Summary of Contents for VistaGRAPHX 2500






































































































Reviews:

No comments

Related manuals for VistaGRAPHX 2500

Brand: Canon Pages: 7

Brand: Canon Pages: 10

Brand: Canon Pages: 6

Brand: Canon Pages: 2

Brand: Canon Pages: 44

Brand: Canon Pages: 63

7215 - LV XGA LCD Projector

Brand: Canon Pages: 8

Brand: Canon Pages: 18

Brand: Canon Pages: 6

Brand: NEC Pages: 83

Brand: NEC Pages: 2

Brand: NEC Pages: 6

Brand: NEC Pages: 4

Showcase Series HT1100

Brand: NEC Pages: 6

Brand: NEC Pages: 99

Brand: NEC Pages: 114

Brand: NEC Pages: 82

Showcase Series HT1100

Brand: NEC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands