Eizo SCD 19102 Instruction Manual Download Page 29

Page: 29 / 104

Connecting

6.8 Installing/removing the display stand and cable for the SCD 19102

SCD 19102 / SMD 19102
Instruction Manual, 05/2008, A5E01588521A-002

6.8

Installing/removing the display stand and cable for the SCD 19102

CAUTION

Do not use screws of excessive length (Page 21)
Screws which are too long can damage mechanical and electronic components of the unit.

Attach the connecting cable before mounting the foot on the display.

Fit the screws on the mounting plate loosely.

Place the display with the loosely fitted screws on the display foot:

First insert two screws into the bottom two drilled holes of the display stand.

Then insert the remaining screws into the top two drilled holes.

Slowly lower the display.

Summary of Contents for SCD 19102









































































































Search results

Summary of Contents for SCD 19102

Reviews:

Related manuals for SCD 19102

Brands by name

Popular brands

Eizo SCD 19102, Instruction Manual

Search results

Summary of Contents for SCD 19102

Reviews:

Related manuals for SCD 19102

Brands by name

Popular brands