manualshive.com logo in svg

Edge-Core ECS4120-28F, Reference Manual, Page: 584 / 938

Share
Download
Edge-Core ECS4120-28F Reference Manual Download Page 584

Chapter 21

  |  VLAN Commands

Configuring VLAN Translation

–  584  –

Configuring VLAN Translation

QinQ tunneling uses double tagging to preserve the customer’s VLAN tags on 
traffic crossing the service provider’s network. However, if any switch in the path 
crossing the service provider’s network does not support this feature, then the 
switches directly connected to that device can be configured to swap the 
customer’s VLAN ID with the service provider’s VLAN ID for upstream traffic, or the 
service provider’s VLAN ID with the customer’s VLAN ID for downstream traffic.

This section describes commands used to configure VLAN translation.

switchport

vlan-translation

This command maps VLAN IDs between the customer and service provider.

Syntax

switchport vlan-translation

 

original

-

vlan

 

new-vlan

no switchport vlan-translation

 

original

-

vlan

original

-

vlan

 - The original VLAN ID. (Range: 1-4094)

new

-

vlan

 - The new VLAN ID. (Range: 1-4094)

Default Setting 

Disabled

Command Mode 

Interface Configuration (Ethernet)

Command Usage 

◆

If the next switch upstream does not support QinQ tunneling, then use this 
command to map the customer’s VLAN ID to the service provider’s VLAN ID for 
the upstream port. Similarly, if the next switch downstream does not support 
QinQ tunneling, then use this command to map the service provider’s VLAN ID 
to the customer’s VLAN ID for the downstream port. Note that one command 
maps both the 

original-vlan

 to 

new-vlan

 for ingress traffic and the 

new-vlan

 to 

original-vlan

 for egress traffic on the specified port.

For example, assume that the upstream switch does not support QinQ 
tunneling. If the command 

switchport vlan-translation 10 100

 is used to map 

VLAN 10 to VLAN 100 for upstream traffic entering port 1, and VLAN 100 to 
VLAN 10 for downstream traffic leaving port 1, then the VLAN IDs will be 
swapped as shown below.

Table 113: VLAN Translation Commands

Command

Function

Mode

switchport vlan-translation

  Maps VLAN IDs between the customer and service provider IC

show vlan-translation

Displays the configuration settings for VLAN translation

PE

Summary of Contents for ECS4120-28F











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments