manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 75

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

75 

then the memory may be corrupt, or the print head connector faulty. 

Under normal circumstances this warning just confirms that the print head type has been changed. 

The defaults for VOD, modulation, etc., will be used, until the user enters a new print head code in 

the SETUP menu. 

If  the  wrong  type  of  print  head  has  been  detected  for  any  reason,  the  modulation  frequency, 

voltage, etc. will all be incorrect. Therefore, the jet will not break up properly, and a phase fault 

(2.02) may occur when starting the jet, or poor print quality may result. 

9.4.11.

 

3.10 Charge Calibration Range 

Contact your local EC-JET distributor if this error is reported. 

9.4.12.

 

3.11 Safety Override Detected 

This warning message alters the user when the safety override link is fitted. 

WARNING: DO NOT START THE PRINTER WHEN THIS ERROR MESSAGE IS PRESENT. 

PRINTER SAFETY CIRCUITS AND SENSORS WILL NOT BE FUNCTIONING. 

IN THE EVENT OF THIS ERROR MESSAGE OCCURRING, SWITCH OFF THE 

PRINTER 

AND 

CONTACT 

YOUR 

LOCAL 

EC-JET 

DISTRIBUTOR 

IMMEDIATELY. 

9.4.13.

 

3.12 Low Pressure 

When starting the jet the printer has detected a loss of ink pressure, which will affect the printer’s 

performance. 

Possible causes 

●     

The main ink filter is blocked. 

●     

Pump output is low. 

Contact your local EC-JET distributor. 

9.4.14.

 

3.14 Over Speed (Variable Data) 

This  indicates  that  the  printer  has  missed  at  least  one  pattern  because  it  cannot  generate  the 
pattern’s  variable  data  (e.g.  sequential  numbers)  at  the  required  rate  -  i.e.  the  printer  was  still 
generating pixel data for the next “print go” when the “print go” occurred. 

The warning applies to the current pattern - it is reset automatically when printing is restarted. 

Possible cause 

●

 

The  amount  of  variable  data  in  the  pattern  is  too  long  for  the  current  rate  of  print 

triggers. Reduce the amount of variable data, if possible. 

 

NOTE:  This  warning  indicates  the  printer  cannot  generate  pixels  fast  enough,  whereas  System 

Warning 3.02 indicates the printer cannot print the rasters fast enough.. 

This warning is only likely to occur for fast rasters (e.g. rasters smaller than 16 drops for 

Micro print head), where pixel generation by the software is slower than the rate at which 

the hardware can print rasters. 

 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands