EC-PACK EC-JET 2000 Manual Download Page 103

Page: 103 / 107

User Manual The1.1 version of 2018 Guangzhou EC-PACK CO.LTD

103

System enclosure: Stainless steel grade 304

Ink tank: Black HDPE

Solvent tank: Nature HDPE

Capacity

Ink tank: 1600ml approximately

Solvent tank: 1600ml approximately

Pressure

Pressure range: Up to 4.48 bar (65 p.s.i.) normal operating pressure

Maximum pressure: 6.2 bar (90 p.s.i.) maximum under fault conditions

Level Control

Ink tank sense low: Warning reported at approximately 400ml

Solvent tank sense low: Warning reported at approximately 400 ml

Performance

Solvent consumption: <10ml/h at 20 Celsius ambient using EC1240 MEK black ink

Memory Capacity

Message storage capacity: 2 areas, 32 messages each area

Logo storage capacity: Up to 100 logos

Chinese character: 12000 inside

Printhead

Types

Micro: 40 micron

Midi: 50 micron, 60 micron and 70 micron

Construction

Printhead:

Polyformaldehyde(POM)

Cover: Stainless steel grade 304

Minimum Conduit bend radius: 230mm

Dimensions

Conduit length: 2m or 4m

Conduit diameter: 20mm

Print head dimensions

：

Diameter 42mm, length 243mm

Throw Distance (recommended)

Micro

：

3.5mm

Midi

：

10mm

Summary of Contents for EC-JET 2000












































































































Search results

Summary of Contents for EC-JET 2000

Reviews:

Brands by name

Popular brands

EC-PACK EC-JET 2000, Manual

Search results

Summary of Contents for EC-JET 2000

Reviews:

Brands by name

Popular brands