manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 66

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

66 

 

8.4.

 

Quick Maintenance Mode 

This  qiuck  maintenance  mode  is  for  users  requesting  to  maintain  and  repair  the  machine 

urgently,  but  the  EC-JET  authorized  engineers  can’t  come  on  users’  site.  Sending  EC2000 

machines to agents or resellers by courier for maintenance or repairing, easy operation, no 

need to empty the ink and solvent tank. 

8.4.1.1.

 

Open the ink system door; 

8.4.1.2.

 

Hold the ink system and draw out until it can’t move; 

8.4.1.3.

 

Take  out  the  ink  tank,  put  a  clean  cloth  or  paper  under  the  ink  tank,  unscrew  the 

connector of the ink routine, take out the ink dip tube and level sensor carefully then put 

into the SMART bottle, show as following picture, screw the connector of routine. 

 

 

 

 

         

 

 

8.4.1.4.

 

Remove  the solvent  tank, pour the solvent to  a container(about 2 litre) and tighten the 

cap. Then take a mark on it. 

8.4.1.5.

 

Screw the ink tank and solvent tank cap, then store in case    avoiding high temperature 

and fire. 

8.4.1.6.

 

Clean  the  SMART  ink  and  solvent  bottle  and  put  in  the  ink-system  bracket,  setup  the 

bracket, screw the thumb and close the ink-system door. 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands