EC-PACK EC-JET 2000 Manual Download Page 23

Page: 23 / 107

User Manual The1.1 version of 2018 Guangzhou EC-PACK CO.LTD

3.10.

Switch off the Printer

3.10.1.

Switch off the printer when jet running or printing:

Press

key and it will have a pop-up box to set “automatic switch off the printer” to Yes.

Printer will power off automatically after finishing shutdown procedure and shutdown delay.

3.10.2.

Switch off the printer when jet stop:

Press

key and press OK in the pop-up box. The printer will switch off the printer

immediately.

3.10.3.

Emergency power off

Rotate the power switch in the right side of the printer to left directly and the printer will power

off immediately.

NOTE: I

f not emergency,Don’t power off directly when the printer is printing or running jet . This

will lead to the printhead failture. If any problems, it needs to clean the system thoroughly for

once.

3.11.

Check the Condition of Printer

The current condition can be seen in Home, including the jetting status, ink/solvent level and

current warning message of the printer.

Summary of Contents for EC-JET 2000












































































































Search results

Summary of Contents for EC-JET 2000

Reviews:

Brands by name

Popular brands

EC-PACK EC-JET 2000, Manual

Search results

Summary of Contents for EC-JET 2000

Reviews:

Brands by name

Popular brands