manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 24

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

24 

 

3.11.1.

 

Status line from the top 

 

Show the jetting status of the printer. 

◆

 

Jet off -- The jet has been stopped.   

◆

 

Jet running -- The jet is running but printing is stopped. 

◆

 

Printing -- The jet is running and the printer is ready to print. 

3.11.2.

 

Solvent       

Show status of solvent level check.       

◆

 

OK - Solvent level is acceptable. 

◆

 

LOW - Add one bottle of solvent.                                             

3.11.3.

 

Ink     

Show status of ink level check.   

◆

 

OK - Ink level is acceptable. 

◆

 

LOW - Add one bottle of ink.           

 

The ink and solvent levels should show OK. If not, they must be refilled with the correct ink or 

solvent. 

3.11.4.

 

Current warning message 

Current warning messages of the printer are listed in the warning message list. 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands