manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 4

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

4 

6.4. Back up .......................................................................................................... 37 
6.6Reset To Factory Defaults ................................................................................ 39 
6.7.Upgrade ........................................................................................................... 40 
6.8.Information ..................................................................................................... 41 
6.9.ID .................................................................................................................... 42 

7. Diagnostic ................................................................................................................ 43 

7.1. Cleaning Pump Purge..................................................................................... 44 
7.2. Start Jet ........................................................................................................... 45 
7.3. Stop Jet ........................................................................................................... 46 
7.4. Quick Jet ........................................................................................................ 46 
7.5. Start Print ....................................................................................................... 46 
7.6. Stop Print ....................................................................................................... 47 
7.7. Test Print ........................................................................................................ 47 
7.8. Clear Nozzle ................................................................................................... 48 
7.9. Clean Printer .................................................................................................. 49 
7.10. Valve Test ..................................................................................................... 55 
7.11. Monitor Jet ................................................................................................... 57 
7.12. Set Pressure .................................................................................................. 58 

8. Daily Maintenance ................................................................................................... 59 

8.1. Cleaning the Printer Cabinet .......................................................................... 59 

8.1.1. General .................................................................................................................. 59 

8.1.2. Ink Spillages .......................................................................................................... 59 

8.1.3. Clear Nozzle, See Chapter 7.8 .............................................................................. 60 

8.1.4. Cleaning the Print Head ........................................................................................ 60 

8.2. Replenishing Ink and Solvent ........................................................................ 61 

8.2.1. NOTE: ................................................................................................................... 61 

8.2.2. EC2000 Consumable Verification ......................................................................... 61 

8.2.3. Refilling the Ink or Solvent: .................................................................................. 63 

8.3. Cleaning/Replacing the Air Filter .................................................................. 64 

8.3.1. Cleaning and Replacement of Air Inlet Filter ....................................................... 64 

8.3.2. Cleaning/Replacing the Air Outlet Filter............................................................... 65 

8.4. Quick Maintenance Mode .............................................................................. 66 

9. Warning and Fault Messages ................................................................................... 68 

9.1. Warning and Fault Messages ......................................................................... 68 
9.2. Summary of Warning Messages..................................................................... 68 

9.2.1. System Failures ..................................................................................................... 68 

9.2.2. Print Failures ......................................................................................................... 68 

9.2.3. System Warnings ................................................................................................... 68 

9.3. System Failures .............................................................................................. 69 

9.3.1. Print Failures ......................................................................................................... 69 

9.3.2. 2.00 Print Head Temperature ................................................................................. 70 

9.3.3. 2.01 Deflector Voltage ........................................................................................... 70 

9.3.4. 2.02 Charge ........................................................................................................... 70 

9.3.5. 2.03 Velocity Of Drop

（

VOD

）

........................................................................... 71 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands