EC-PACK EC-JET 2000 Manual Download Page 69

Page: 69 / 107

User Manual The1.1 version of 2018 Guangzhou EC-PACK CO.LTD

3.10 Charge Calibration Range

3.11 Safety Override Detected

3.12 Low Pressure

3.13 Modulation

3.14 Over Speed (variable data)

9.3.

System Failures

System failures occur when the software detects a condition which prevents normal printer

operation.

These prevent normal printer operation. Contact with EC-JET distributor when necessary.

WARNING: LETHAL VOLTAGE. UNKNOWN HIGH VOLTAGES MAY

BE PRESENT WITH SOME SYSTEM FAILURES. DO NOT TAMPER

WITH THE PRINTER OR PRINTHEAD. WAIT UNTIL THE FAILURE

SHUTDOWN IS COMPLETE.

9.3.1.

Print Failures

These occur when the software detects a problem which affects printing.

When a Print Failure occurs a message is displayed on the screen status line and a jet shutdown

sequence is started.

The internal alarm buzzer is switched on, the “print ready” line set low and the alarm relay is

activated(if enabled).

When the shutdown sequence is complete the Print Failure screen is displayed:

The user should normally select

to reset the printer.

Following a print failure shutdown, the software sets:

Summary of Contents for EC-JET 2000












































































































Search results

Summary of Contents for EC-JET 2000

Reviews:

Brands by name

Popular brands

EC-PACK EC-JET 2000, Manual

Search results

Summary of Contents for EC-JET 2000

Reviews:

Brands by name

Popular brands