manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 59

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

59 

8.

 

  Daily Maintenance 

There  are  two  levels  of  daily  maintenance:  User  -  performed  by  the  operator,  and  Service  - 

performed by EC-JET Trained Service Engineers. 

User maintenance is required daily (each time the printer is used) and weekly. 

Service (scheduled) maintenance is required after every 4000 jet running hours. 

The following table defines the user maintenance requirements for EC-JET printers: 

 

 

 

Monitor 

Clean 

Change/Add 

Printer Cabinet 

Daily/Each time is used 

Weekly/On demand 

No need 

Print Head 

Daily/Each time is used 

Daily/On demand 

No need 

Ink and Solvent 

Start up/In use 

No need 

On demand 

Air Filter 

Daily on many dust or easy 

polluted/Once a week 

Weekly/By need 

On demand 

 

 

8.1.

 

Cleaning the Printer Cabinet 

8.1.1.

 

General 

The exterior of the printer can be cleaned using a soft cloth lightly soaked in a mold detergent. 

CAUTION: Do not use abrasive cleaning agents. Do not use excessive pressure when wiping over 

the LCD screen; excessive pressure can cause damage. 

8.1.2.

 

Ink Spillages 

If  ink  is  accidentally  spilled  onto  the  exterior  of  the  printer  the  following  procedures  are 

recommended: 

 

WARING:  ALWAYS  WEAR  RUBBER  GLOVES  AND  SAFETY  GLASSER 

WHEN  HANDLING  SOLVENT.  DO  NOT  USE  SOLVENT  IN  CONFINED 

AREAS WITHOUT ADEQUATE VENTILATION. 

 

CAUTION: USE ONLY EC-JET SOLVENT. ENSURE THAT THE SOLVENT 

MATCHES THE TYPE USED IN THE PRINTER. 

Do not use excessive amounts of solvent. It is not recommended that solvent is used 

frequently  to  remove  ink  from  the  front  panel  and  LCD  screen  as  this  can  lead  to 

deterioration of the membrane surface. Better to use a soft cloth with solvent to wipe 

lightly. 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands