manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 60

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

60 

8.1.3.

 

Clear Nozzle, See Chapter 7.8 

8.1.4.

 

Cleaning the Print Head 

The EC2000 has a "Automatic nozzle cleaning" program. Under normal circumstances, the nozzle 

is dirty.  The  nozzle cleaning  can be  performed automatically by  executing the "cleaning nozzle" 

program. If necessary, it can be repeated 2-3 times. 

Only  when  the  machine  “cleaning  nozzle  program”  fails,  or  if  the  nozzle/contamination  of  the 

nozzle  causes  the  contamination  of  the  nozzle  to  be  particularly  serious,  it  is  necessary  to 

manually clean the nozzle. 

 

 

CAUTION: USE ONLY EC-JET SOLVENT. ENSURE THAT THE SOLVENT 

MATCHES THE TYPE USED IN THE PRINTER. 

 

WARNING:  POTENTIALLY  LETHAL  VOLTAGES  ARE  PRESENT 

WITHIN  THE  PRINTHEAD.  BE  SURE  ALL  POWER  IS  SWITCHED  OFF 

BEFORE  THE  PRINTHEAD  IS  OPENED  FOR  INSPECTION  AND 

CLEANING. 

                       

Print head Cleaning Procedure

 

After wearing approved, solvent resistant gloves: 

Remove the print head cover and hold the print head as shown below. Place a suitable container 

underneath and wash the entire printed circuit board (PCB) surface with the appropriate solvent. 

Do not use the wrong solvent; make sure it is the solvent corresponding to the ink type being used 

in the printer. 

Simply squirt the solvent in short bursts onto the affected parts with a short delay between bursts 

to allow ink to dissolve.

 The surplus solvent will run down the print head and can be collected in 

the container for disposal. 

Allow the print head to dry completely by letting it stand for a few minutes. Do not dry the print 

head  with  a  cloth  or  towel  as  this  may  leave  fibers  that  could  interfere  with  the  printed  drops. 

Particular care should be taken to ensure that the space between the nozzle and charge electrode is 

free of solvent. If not, it can usually be removed by inverting the wash bottle and blowing off the 

excess solvent. 

 

WARNING:  MOST  INK  BASES  ARE  FLAMMABLE.  IT  IS  THEREFORE 

IMPORTANT  TO  DISPOSE  OF  THE  WASTE  CLEANING  FLUID  IN 

ACCORDANCE WITH LOCAL REGULATIONS.

 

 

CAUTION: DO NOT BE TEMPTED TO IMMERSE THE PRINTHEAD IN SOLVENT OR 

AN  ULTRASONIC  BATH.  THIS  MAY  DAMAGE  THE  PRINTHEAD  AND  WILL  VOID 

THE WARRANTY. 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands