manualshive.com logo in svg

EC-PACK EC-JET 2000, Manual

Share
Download
EC-PACK EC-JET 2000 Manual Download Page 47

 

User Manual          The1.1 version of 2018                                    Guangzhou EC-PACK CO.LTD 

 

47 

has a lower level function than the 

  button which sets, for example, “Phase” option setting 

will automatically set to“On” when pressed “Start” but the current statu will not. 

 

7.6.

 

Stop Print 

Stops printing but does not shutdown the jet. 

The following message will be displayed while stopping printing: 

     

7.7. 

Test Print

 

Select  this option to  issue a  trigger the print command. Triggered print command  of test print is 

same as the photocell trigger command. 

This command is valid only when the photocell mode from setup menu is set to Triggered and the 

printer is on the status of printing. This command is invalid if the photocell set to OFF. 

It will not print if using the shaft encoder and the production line doesn’t start. Only print when 

the production line starts. 

Summary of Contents for EC-JET 2000












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands