Dynapac CC1000 e Instruction Manual Download Page 54

Page: 54 / 130

Machine description

4812164901_A.pdf

2022-11-14

Safety instructions for maintenance

Do not open the cover of the battery system.
No maintenance inside the battery system is
required and possible repairs shall be
performed only by authorized personnel
(authorized by supplier and Dynapac).

Do not connect or disconnect power terminals
or signal interface terminal under the load.

Keep power terminals and signal interface
terminal connected when cleaning the battery
system.

Do not spray high pressure waterjet to pack lid
seams, power terminals, signal interface
terminal, and venting valve.

Make sure that power terminals and signal
interface terminal are clean before connecting
them.

Safety instructions for dismounting

Safety instructions for lifting

Obey the lifting instructions to prevent
dropping the battery system. See chapter Lifting
instructions.

Make sure that the dismounting area is clear
before dismounting the battery system from
machine.

Falling object hazard - Do not stand under the
hoisted battery system.

Crushing hazrad - Do not place any body part
between the battery system and machine frame
when lifting the battery system.

Summary of Contents for CC1000 e



































































































































Search results

Summary of Contents for CC1000 e

Reviews:

Related manuals for CC1000 e

Brands by name

Popular brands

Dynapac CC1000 e, Instruction Manual

Search results

Summary of Contents for CC1000 e

Reviews:

Related manuals for CC1000 e

Brands by name

Popular brands