Dynapac CC1000 e Instruction Manual Download Page 3

Page: 3 / 130

2000h-

Maintenance

4812164901_A.pdf

2022-11-14

Table of Contents

Introduction .............................................................................................................................. 1

The machine ............................................................................................... 1

Intended use ............................................................................................... 1

Training ....................................................................................................... 1

Signal symbols and meaning ...................................................................... 1

Safety information ....................................................................................... 1

General ....................................................................................................... 2

Safety - General instructions.................................................................................................... 3

Safety - when operating ........................................................................................................... 5

Work driving ................................................................................................ 5

Driving near edges ...................................................................................... 6

Special instructions .................................................................................................................. 7

Standard lubricants and other recommended oils and fluids ...................... 7

Higher ambient temperatures, above +40°C (104°F).................................. 7

Lower ambient temperature - Freeze risk ................................................... 7

Temperatures.............................................................................................. 7

Battery pack ................................................................................................ 8

High pressure cleaning ............................................................................... 8

Fire fighting ................................................................................................. 9

Fire extinguisher.......................................................................................... 9

Roll Over Protective Structure (ROPS) ..................................................... 10

Technical specifications ......................................................................................................... 11

Vibrations - Operator station ..................................................................... 11

Noise level................................................................................................. 11

Slopes ....................................................................................................... 11

Dimensions, side view............................................................................... 12

Dimensions, top view ................................................................................ 13

Weights and volumes................................................................................ 14

Working capacity....................................................................................... 14

General ..................................................................................................... 15

Summary of Contents for CC1000 e



































































































































Search results

Summary of Contents for CC1000 e

Reviews:

Related manuals for CC1000 e

Brands by name

Popular brands

Dynapac CC1000 e, Instruction Manual

Search results

Summary of Contents for CC1000 e

Reviews:

Related manuals for CC1000 e

Brands by name

Popular brands