Durr Dental Tornado 1 Installation And Operating Instructions Manual Download Page 44

Page: 44 / 48

Error

Possible cause

Remedy

Defective membrane drying unit

❯

Replace the membrane drying
unit.

❯

Inform a Service Technician.

Cup seal worn at the piston or
defective

❯

Replace the cup seal or the
entire piston.

Water dripping from air con-
sumers

Maintenance work not carried
out regularly (without membrane
drying unit)

❯

Regularly drain the condensa-
tion water from the pressure
tank, see "9.4 Draining the
condensation water"

Defective membrane drying unit

❯

Inform a service technician.

Working cycles of the com-
pressor are very short, even if
only small amounts of air are
removed

Condensed water in the tank

❯

Drain off condensed water

❯

The dry air units of compres-
sors fitted with dry air units
need to be checked and
replaced, if applicable.

Troubleshooting

9000-610-60/02 1909V007

Summary of Contents for Tornado 1

















































Search results

Summary of Contents for Tornado 1

Reviews:

Brands by name

Popular brands

Durr Dental Tornado 1, Installation And Operating Instructions Manual

Search results

Summary of Contents for Tornado 1

Reviews:

Brands by name

Popular brands