manualshive.com logo in svg

Durr Dental Tornado 1, Installation And Operating Instructions Manual

Share
Download
Durr Dental Tornado 1 Installation And Operating Instructions Manual Download Page 41

❯

Replace the filter cover and close.

Sintered filter

❯

Unscrew and remove the filter housing.

❯

Remove the sintered filter.

❯

Insert a new sintered filter.

❯

Replace the filter housing and close.

14 Taking out of use

14.1 Taking the unit out of use

If the unit is not to be used for a prolonged
period of time, we recommend that it is properly
shut down and taken out of use.
To do this, the accumulated condensation water
from the unit must be drained.

❯

Switch on the unit and wait until the cut-off
pressure is reached.

Membrane drying unit

❯

While the compressor unit is running, open the
condensate drain valve on the membrane dry-
ing unit. When no more condensation water
emerges, close the condensate drain valve.

❯

Switch off the device.

Pressure tank

❯

Open the condensate drain valve.
Once the start-up pressure has been reached
the compressor will switch on.

❯

With the compressor switched on and the con-
densate drain valve open, wait until no more
condensation water emerges.

❯

Switch off the unit.

❯

Close the condensate drain valve when no
more air escapes.

❯

Disconnect all power from the device.

❯

Disconnect the compressed air connection on
the quick release coupling.

Usage

9000-610-60/02 1909V007

39

EN

Summary of Contents for Tornado 1

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands