manualshive.com logo in svg

Durr Dental Tornado 1, Installation And Operating Instructions Manual

Share
Download
Durr Dental Tornado 1 Installation And Operating Instructions Manual Download Page 26

7

Transport

WARNING
Risk of explosion of the pressure tank
and pressure hoses

❯

The pressure tank and the pressure
hoses must be vented before they are
stored or transported.

❯

Protect the unit against moisture, dirt and
extreme temperatures during transport (refer to
the section on "Ambient conditions").

❯

Always make sure that the condensate collec-
tor chamber is empty before transporting the
unit ("14.1 Taking the unit out of use").

❯

Always transport the unit in an upright position.

❯

Only transport the unit using the transport han-
dles provided.

8

Installation

8.1

Remove the transport locks

For safe transport, the unit is secured with foam
padding blocks and a transport strap.

❯

Cut and remove the transport strap.

❯

Remove the foam padding blocks.

2

1

1

Transport strap

2

Foam padding blocks

8.2

Establishing the compressed
air connection

The supplied flexible pressure hose
between the pipe system and the com-
pressor prevents vibrations from being
transmitted and thus reduces noise. This
ensures safe and reliable operation.

❯

Connect the pre-assembled connecting sleeve
of the pressure hose to the quick release cou-
pling.

❯

Measure the required length of the pressure
hose and shorten if necessary.

❯

Press a fitting hose connector (not included in
the scope of delivery) onto the pressure hose
(internal diameter 10 mm) and secure it with a
hose clip.

❯

Connect the connecting sleeve of the pressure
hose to the compressed air tube.

Assembly

24

9000-610-60/02 1909V007

EN

Summary of Contents for Tornado 1

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands