manualshive.com logo in svg

Durr Dental Tornado 1, Installation And Operating Instructions Manual

Share
Download
Durr Dental Tornado 1 Installation And Operating Instructions Manual Download Page 40

13.2 Replacing the air intake filter

Units without a noise reduction hood

❯

Switch off the compressor at the pressure
switch.

❯

Disconnect all power from the device.

❯

Release the filter cover by rotating it 

anti-

clockwise

 and then take it off.

❯

Remove the air intake filter.

❯

Insert a new air intake filter.

❯

Place the filter cover in position and lock it by
turning it 

clockwise

.

Units with a noise reduction hood

❯

Switch off the compressor at the rotary switch
of the pressure switch.

❯

Disconnect all power from the device.

❯

Take off the noise reducing hood and the foam
filter cover.

2

1

❯

Release the filter cover by rotating it 

anti-

clockwise

 and then take it off.

2

1

❯

Remove the air intake filter.

❯

Insert a new air intake filter.

❯

Place the filter cover in position and lock it by
turning it 

clockwise

.

❯

Fit the the foam filter cover and the noise
reducing hood.

13.3 Replacing the filter of the

membrane drying unit

Fine/sterile filter

❯

Switch off the unit.

❯

Disconnect all power from the device.

❯

Unscrew and remove the filter cover.

❯

Remove the fine/sterile filter.

❯

Insert the new fine/sterile filter.

Usage

38

9000-610-60/02 1909V007

EN

Summary of Contents for Tornado 1

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands