Vigor130 Series User’s Guide
164
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
o
o
a
a
m
m
l
l
b
b
This command is used to test if the connection between CPE and CO is OK or not.
adsl oamlb [n][type]
adsl oamlb chklink [on/off]
adsl oamlb [log_on/log_off]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
P
P
a
a
r
r
a
a
m
m
e
e
t
t
e
e
r
r
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
n
It means the total number of transmitted packets.
type
It means the protocol that you can use.
1 – for F4 Seg-to-Seg (VP level)
2 – for F4 End-to-End (VP level)
4 – for F5 Seg-to-Seg (VC level)
5 – for F5 End-to-End (VC level)
chklink
Check the DSL connection.
Log_on/log_off
Enable or disable the OAM log for debug.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl oamlb chklink on
OAM checking dsl link is ON.
> adsl oamlb F5 4
Tx cnt=0
Rx Cnt=0
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
v
v
c
c
i
i
l
l
i
i
m
m
i
i
t
t
This command can cancel the limit for vci value.
Some ISP might set the vci value under 32. In such case, we can cancel such limit manually
by using this command. Do not set the number greater than 254.
adsl vcilimit
[n]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
P
P
a
a
r
r
a
a
m
m
e
e
t
t
e
e
r
r
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
n
The number shall be between 1 ~ 254.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl vcilimit 33
change VCI limitation from 32 to 33.
Summary of Contents for Vigor130
