Draft - Not for Release - 9510-065-D-3-10
20
NC
NO
P7
20 19 18 17 16 15 14 13 12 11 10 9 8 7
6
5
4
3
2 1
1 2 3
4
5
6
UL 325
Terminal
UL 325
Terminal
UL 325
Terminal
UL 325
Terminal
Primary Operator
NC
NO
P7
20 19 18 17 16 15 14 13 12 11 10 9 8 7
6
5 4 3
2 1
1 2 3
4
5
6
UL 325
Terminal
UL 325
Terminal
UL 325
Terminal
UL 325
Terminal
Secondary Operator
2.8 Primary / Secondary Dual Gate Operators Wiring
Connect a jumper wire
from terminal #2 to #4 in
primary operator terminal
ONLY
when using the
plug-in loop detector.
Plug loop detector into
Primary Operator’s
Exit
Loop Port
.
Dual Channel
9409
24 Volt Power
Relay
Com
Green to primary operator
chassis ground.
Com to #1
Normally Open to #6
Reverse loop lead-in
wires are wired in series.
Automatic
Exit Loop
Reverse
Loop
Reverse
Loop
Loop Lead-In Wires
Loop Detector
3-Wire Receiver
250 mamp. max.
W
A
RNING
MOVING GATE CAN CAUSE
O
p
erate gate onl
y when gate area i
s i
n
si
ght
and free of people and obstructions.
D
o not
al
low chi
ldr
en t
o
pl
ay i
n
gat
e
ar
ea
or operate gate.
Do not stand in gate path or walk through
path while gate is moving.
Read ow
ner’s m
a
nual and safety instructions.
SERIOUS INJURY OR DEATH
W
A
RNING
MOVING GATE CAN CAUSE
O
p
erate gate onl
y when gate area i
s i
n
si
ght
and free of people and obstructions.
D
o not
al
low chi
ldr
en t
o
pl
ay i
n
gat
e
ar
ea
or operate gate.
Do not stand in gate path or walk through
path while gate is moving.
Read ow
ner’s m
a
nual and safety instructions.
SERIOUS INJURY OR DEATH
Secondary Entrapment
Protection Devices
Secondary
Operator
Primary
Operator
To Close Photo #2
To Open Edge #3
To Open Edge #3
To Open Edge #3
To Common #5
To Common #5
To Open Photo #1
To Open Photo #1
Fence
Gate
Opening Non-Contact Sensor
Closing Non-Contact Sensor
Opening Contact Sensor
Opening Contact Sensor
Opening Non-Contact Sensor
Fence
Gate
Y
ellow
Brown
Orange
Gray
Green to secondary operator
chassis ground.
Y
ellow
Brown
Orange
Gray
Primary SW 1,
switch 3
must be
OFF
.
1 1
ON
2
3
45
6 6 7 7
8 8
Interconnection Cable
Sold separately from DoorKing.
5 wires used (8 - 18 A
W
G wires total).
Note: 4-wire radio
receiver, or any other
opening devices get
wired to primary
operator ONLY as
shown on page 17.
Note: Secondary operator ‘s
DIP-switches MUST be set for
the dual operators to cycle
correctly. See page 23 for more
information about dual operator
DIP-switch settings.
Note: If relay wire is
connected to terminal #2,
gate fully opens. If relay
wire is connected to
terminal #5, gate opens to
the middle limit nut setting
(Partial open). See page 24
for limit nut settings.
Note: Secondary
entrapment devices will
reverse and open gate to
the middle limit nut setting
(Partial open) if the
opening device is
connected to terminal #5.
SW 1 is Upside-Down on Board
4404-010
4404-010
•
Requires AC power to
each
operator.
•
Both
operator DIP-switches must be set.
•
Connect all control devices, auxiliary
devices and loops to the
primary
operator
only
.
•
Separate power source for photocells.
Summary of Contents for Series 9500
Page 2: ......
