DoorKing Series 9500, Owner'S Manual

Page: 21 / 36

9510-065-D-3-10 - Draft - Not for Release 19
TIME DELA
Y
EXIT LOOP
LMT
LMT
REVERSE LOOP
REV SENSE
OPEN
REV SENSE CLOSE
1
ON
2 3 4 1
ON
2 3 4 5 6 7 8
NC
NO
P8
P7
P6
4404-010
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
W ARNI
NG
MO VIN G G
ATE CA N C AU
SE
Op era te g ate on
ly wh en g ate are a is in s
igh t
and fre e o
f pe op le an d o bst ruct ion
s.
Do n
ot al low ch ildre n to
pla y in ga te are a
or o pe rate ga te.
Do n
ot st and in ga te p ath or
wa lk th rou gh
path wh ile gate is mo
vin g.
Read ow ner
’s m anu al a nd sa fety ins
truc tion s.
SE RIO
US INJ UR Y O
R D EAT H
Reverse
Reverse
Automatic Exit
4 Ft.
Min.
4 Ft.
Min. to avoid gate
movement inter
ference.
9410
Note: Loop detector wiring is shown for
DoorKing plug-in loop detectors P/N 9410-010
(Single Channel). DoorKing plug-in loop
detector P/N 9409-010 (Dual Channel) can be
used for certain applications. If other loop
detectors are used, refer to the installation
instructions supplied with those detectors for
wiring and separate power instructions.
9410
Single Channel Single Channel
2.7 Loop Detector Wiring
Loop Lead In Cable
Loop Lead In Wires
DoorKing
Plug-in
Loop Detectors
Note: See page 22,
Reverse/Stop Input
for SW 1, switch 7
options.
A B
SW 1 is Upside-Down on Board
1 1
ON
23 45 6 6 7 8 8
Automatic Exit Loop
Automatically opens the gate for exiting vehicles
without having to use a transmitter or keypad. The exit
loop can be placed 20-100 feet away from the gate so
the gate has started opening or has completely
opened by the time you drive up to it.
Reverse/Stop Loops
Reverse/Stop loops are placed on each side of the gate
to prevent the gate from closing on a vehicle in the
gate’s path. They will stop or reverse the cycling of the
gate while a vehicle is in or near the gate’s pathway.
To protect the operator from accidentally closing on vehicles in the gate’s path, DoorKing highly recommends that loops and
loop detectors be installed. Loops are laid underneath, cut into asphalt or concrete driveways or buried beneath gravel and earth
driveways. A loop detection system will sense a vehicle like a metal detector and send a signal to the gate operator preventing
the gate from automatically opening or closing on a vehicle when it is in the gate’s path. DoorKing recommends that a licensed
installer perform this work.
Reverse loop
lead-in wires are
twisted approx.
6 twists per foot
and are wired in
series.
A
LOOP 1
B
LOOP 1
Operator
Chassis
Ground
PVC Conduit
Lead-in cable
from loop.
Ground shield at
operator end ONLY.
DoorKing offers a free “ Loop and Loop-Detectors
Information Manual ” PDF located at Doorking’s
web site for more information. www.dkaccess.com
A Lead-In Cable is
typically used to connect
the automatic exit loop
to the loop detector
when distances are
greater than 10 ft
between them.
PVC Conduit
Shielded Twisted Pair
Loop
Wires