6555-065-A-12-18
23
1
2
5
6
11
13A
13B
13E
25
16
17
L1
L2
L3
B-
B+
M
od
e
EPM
0 0 0
SCM se
ries
bas
ic I
/O co
ntro
l
PUS
H
TO
OP
ERA
TE
tec
hni
cia
n u
se
on
ly
MI
N
MA
X
(2) Two 115 VAC
Convenience Outlets
Power is limited
to 250 mA
3-Wire Radio
Receiver
4-Wire
Radio
Receiver
Com
24 V
olt
Relay
3-Pin
Remote
Terminal
1
2
3
Important:
Controls must be installed a minimum
of 6-feet from the gate or installed in such a way
that the person using the control cannot come in
contact with the gate or gate operator.
4.2 Control Wiring
Type of wiring to be used on ALL external devices:
A)
Type
CL2
,
CL2P
,
CL2R
, or
CL2X
.
B)
Other cable with
equivalent
or
better
electrical,
mechanical, and flammability ratings.
NC
NO
P7
OB
CB
OE
CE
G
G
1
ON
1477-010
SW1
2 3 4
4404
#4
#2
#5
#6
#7
#
8
#9
20
19
18
17
16
15
14
13
12
11
10
9
8
7
65
43
2
1
1
2
3
G
3-Button
Station
Jumper
Open
Close
Com
Stop
IMPORTANT:
Leave 3-button control station jumper
pins on 2 & 3 when
NOT
wiring
a 3-button control station to
control board otherwise
operator will
NOT
fuction.
Jumper Pins 1 & 2
ONLY
when
using a 4-wire control station
to
enable
stop terminal #9.
3-Button Control Station Jumper
3-Button Control Station
#1-Relay Com
#2 -Relay
#1-24 Volt Power Com
#3-24 Volt Power
Key Switch
Stand-Alone
Keypad
Stand-Alone
Card Reader
Telephone Entry
Note:
All stand-alone
and telephone entry
devices must use a
separate power source.
#4-Opens gate.
P9
1
2
3
Main Terminal #3 Note:
Exceeding 250 mA of power from this terminal may
cause the circuit board transformer to overheat,
causing intermittent problems.
OP
EN
ST
OP
CLOSE
3
2
1
Factory
Setting
3
2
1
P9
P9
Gate Tracker
Terminal
Gate Tracker -
DoorKing Access Control System (Model 1833, 1835, 1837 or 1838)
tracker system can be connected. This system can keep track of gate operator cycle
count, shorted inputs, loop detector problems, any forced entry attempts, if the gate
has struck anything during the open or close cycle, power interruptions, etc. For more
detailed information refer to the Tracker Installation and Wiring Manual P/N 2358-065.
Gate Tracker
(Quad Box Shown)
FIRE
Fire
Dept Open
Gate will
ONLY OPEN
when this device is activated by authorized
personnel ONLY (fire, police, EMS) and operator has power. Alarm will
sound during entire open cycle. Operator will then go into a hard
shutdown once fully opened. Operator
MUST
be reset to function
normally again. This device
MUST
be mounted in the line-of-site of gate
so authorized personnel can monitor gate movement.
Activation Note:
Activation of this device will
OPEN
gate regardless of the
status of the open direction monitored external entrapment protection
device(s). If gate is opening, and the operator’s
inherent
entrapment
protection system detects an obstruction, the operator will reverse
approx. 2 inches and go into a hard shutdown.
Operator reset button
MUST
be pushed to
function again
OR
cycle operator’s power.
2-Pin
Supplied
Wire
Harness
Com
