Digital Equipment VAXstation 4000 Model 60 Upgrade Manual Download Page 62

Page: 62 / 82

Installing Mass Storage Devices

Install the Hard
Disk Drive

To install the hard disk drive assembly in the BA46 system

enclosure, complete the following steps:

Step

Action

Connect both the SCSI and dc power cables to the

drive(s).

Snap the bracket assembly back into place.

Check the cable routing. For more information on cable

routing, refer to the

VAXstation 4000 Options Installation

Guide

Install the
Removable
Media Drives

The removable media drive assembly may contain one of the

following drives:

RRD42 CDROM drive
RX26 (diskette) drive
TLZ06 cassette tape drive
TZK10 QIC tape drive

To install the removable media drive assembly from the BA46

system enclosure, complete the following steps:

Step

Action

Connect both the SCSI and dc power cables to the drive.

Snap the bracket assembly back into place.

Check the cable routing. For more information on cable

routing, refer to the

VAXstation 4000 Options Installation

Guide

3–20

Summary of Contents for VAXstation 4000 Model 60



















































































Search results

Summary of Contents for VAXstation 4000 Model 60

Reviews:

Related manuals for VAXstation 4000 Model 60

Brands by name

Popular brands

Digital Equipment VAXstation 4000 Model 60, Upgrade Manual

Search results

Summary of Contents for VAXstation 4000 Model 60

Reviews:

Related manuals for VAXstation 4000 Model 60

Brands by name

Popular brands