Chapter 12 Description of Parameter Settings
CFP2000
12.1-06-29
Code
Error name
Normal
mode
Fire Mode
Enable bypass
function
84
W-phase output phase loss (OPHL)
V
V(able to auto-reset)
V
89
RoPd initial rotor position detection error
V
V
V
90
Inner PLC function is forced to stop (FStp)
V
Not-detectable
Not-detectable
93
CPU error
Not
detectable
Not-detectable
Not-detectable
99
CPU Trap error (TRAP)
V
V
Not-detectable
101 CANopen software disconnect 1 (CGdE)
V
Not-detectable
Not-detectable
102 CANopen software disconnect 2 (ChbE)
V
Not-detectable
Not-detectable
103 CANopen synchronous error (CSYE)
V
Not-detectable
Not-detectable
104 CANopen hardware disconnect (CbFE)
V
Not-detectable
Not-detectable
105 CANopen index setting error (CidE)
V
Not-detectable
Not-detectable
106 CANopen slave station number setting
error (CAdE)
V
Not-detectable
Not-detectable
107 CANopen index setting exceed limit (CfrE)
V
Not-detectable
Not-detectable
111 InrCOM Internal communication overtime
error
V
Not-detectable
Not-detectable
142 Auto-tuning error 1 (no feedback current
error) (AUE1)
Not
detectable
Not-detectable
Not-detectable
143 Auto-tuning error 2 (motor phase loss
error) (AUE2)
Not
detectable
Not-detectable
Not-detectable
144 Auto-tuning error 3 (no-load current I
0
measuring error) (AUE3)
Not
detectable
Not-detectable
Not-detectable
148 Auto-tuning error 4 (leakage inductance
Lsigma measuring error) (AUE4)
Not
detectable
Not-detectable
Not-detectable
The Fire mode reset procedure:
When the terminal MIx=58 changes from ON to OFF, the drive starts to run “fire mode reset procedure”,
and determines whether to “Manual reset” or “Auto reset” fire mode according to the selection of
Pr.06-86 bit1.
Wiring Diagram:
1. When AC power is ON, RB1 and RC1 are ON, and RA1 and RC1 are OFF.
2. When operating in fire mode and bypass indication function is disabled, RB1 and RC1 are ON, and
the motor is driven by the drive.
3. When operating in fire mode and bypass indication function is enabled, RA1 and RC1 are ON, and
the motor runs under mains electricity.
Summary of Contents for CFP2000 Series
