manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 111

Troubleshooting and Frequently Asked Questions

111

Please enter the IPv6 

Default Gateway address

Enter the IPv6 default gateway address. 

See 

IPv6 Configuration

.

Please enter a valid IPv6 

DNS Server 1 Address

Enter a valid IPv6 DNS Server1 address. 

See 

IPv6 Configuration

.

Please enter a valid IPv6 

DNS Server 2 Address

Enter a valid IPv6 DNS Server2 address. 

See 

IPv6 Configuration

.

Please enter a valid iDRAC 

Name of up to 63 characters

Enter a valid iDRAC name that is less than or 

equal to 63 characters.

Please enter a valid Domain 

Name of up to 64 characters

Enter a valid domain name that is less than or 

equal to 64 characters.

Please enter a valid Host 

Name of up to 62 characters

Enter a valid host name that is less than or 

equal to 62 characters.

Please enter a value in the 

range of 1 to 4094

Enter a VLAN ID between 1 and 4094. See 

Advanced 

LAN Configuration

.

Please enter a value in the 

range of 0 to 7

Enter a VLAN ID priority value between 0 and 7. 

See 

Advanced LAN Configuration

.

iDRAC communication 

failure. Please power down, 

unplug the system, wait 5 

seconds, apply power and 

power on

Communication with iDRAC has failed. To resolve 

this issue:

1

Turn off the system, and then unplug it.

2

Wait 5 seconds. 

3

Plug the system back in, and then turn it on.

iDRAC hard failure. Please 

power down, unplug the 

system, wait 5 seconds, 

apply power and power on

Connection with iDRAC has failed. To resolve this 

issue:

1

Turn off the system, and then unplug it.

2

Wait 5 seconds. 

3

Plug the system back in, and then turn it on.

RAID configuration failed

USC-LCE failed when creating the RAID 

configuration. To resolve this issue: 

1

Reboot the system.

2

Re-enter USC-LCE by pressing the 

<F10>

 key.

3

Try again to create the RAID configuration.

Table 5-3.  USC-LCE Error Messages and Resolutions 

(continued)

Error Message

Resolution

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands