manualshive.com logo in svg

Dell S4048-ON, Configuration Manual

Share
Download
Dell S4048-ON Configuration Manual Download Page 710

44

Routing Information Protocol (RIP)

The Routing Information Protocol (RIP) tracks distances or hop counts to nearby routers when establishing network connections 
and is based on a distance-vector algorithm.
RIP is based on a distance-vector algorithm; it tracks distances or hop counts to nearby routers when establishing network 
connections.

RIP protocol standards are listed in the 

Standards Compliance

 chapter.

 

Protocol Overview

RIP is the oldest interior gateway protocol.

There are two versions of RIP: RIP version 1 (RIPv1) and RIP version 2 (RIPv2). These versions are documented in RFCs 1058 and 
2453.

RIPv1

RIPv1 learns where nodes in a network are located by automatically constructing a routing data table.

The routing table is established after RIP sends out one or more broadcast signals to all adjacent nodes in a network. Hop counts of 
these signals are tracked and entered into the routing table, which defines where nodes in the network are located.
The information that is used to update the routing table is sent as either a request or response message. In RIPv1, automatic updates 
to the routing table are performed as either one-time requests or periodic responses (every 30 seconds). RIP transports its 
responses or requests by means of user datagram protocol (UDP) over port 520.

RIP must receive regular routing updates to maintain a correct routing table. Response messages containing a router’s full routing 
table are transmitted every 30 seconds. If a router does not send an update within a certain amount of time, the hop count to that 
route is changed to unreachable (a route hop metric of 16 hops). Another timer sets the amount of time before the unreachable 
routes are removed from the routing table.

This first RIP version does not support variable length subnet mask (VLSM) or classless inter-domain routing (CIDR) and is not 
widely used.

RIPv2

RIPv2 adds support for subnet fields in the RIP routing updates, thus qualifying it as a classless routing protocol.

The RIPv2 message format includes entries for route tags, subnet masks, and next hop addresses. Another enhancement included in 
RIPv2 is multicasting for route updates on IP multicast address 224.0.0.9.

Implementation Information

Dell Networking OS supports both versions of RIP and allows you to configure one version globally and the other version on 
interfaces or both versions on the interfaces.

The following table lists the defaults for RIP in Dell Networking OS.

710

Routing Information Protocol (RIP)

Summary of Contents for S4048-ON
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands