
NOTE: ACL resequencing does not affect the rules, remarks, or order in which they are applied. Resequencing merely
renumbers the rules so that you can place new rules within the list as needed.
Table 10. ACL Resequencing
Rules
Resquencing
Rules Before Resequencing:
seq 5 permit any host 1.1.1.1
seq 6 permit any host 1.1.1.2
seq 7 permit any host 1.1.1.3
seq 10 permit any host 1.1.1.4
Rules After Resequencing:
seq 5 permit any host 1.1.1.1
seq 10 permit any host 1.1.1.2
seq 15 permit any host 1.1.1.3
seq 20 permit any host 1.1.1.4
Resequencing an ACL or Prefix List
Resequencing is available for IPv4 and IPv6 ACLs, prefix lists, and MAC ACLs.
To resequence an ACL or prefix list, use the following commands. You must specify the list name, starting number, and increment
when using these commands.
•
IPv4, IPv6, or MAC ACL
EXEC mode
resequence access-list {ipv4 | ipv6 | mac} {
access-list-name StartingSeqNum Step-to-
Increment
}
•
IPv4 or IPv6 prefix-list
EXEC mode
resequence prefix-list {ipv4 | ipv6} {
prefix-list-name StartingSeqNum Step-to-Increment
}
Examples of Resequencing ACLs When Remarks and Rules Have the Same Number or Different Numbers
Remarks and rules that originally have the same sequence number have the same sequence number after you apply the
resequence
command.
The example shows the resequencing of an IPv4 access-list beginning with the number 2 and incrementing by 2.
Dell(config-ext-nacl)# show config
!
ip access-list extended test
remark
4
XYZ
remark
5
this remark corresponds to permit any host 1.1.1.1
seq
5
permit ip any host 1.1.1.1
remark
9
ABC
remark
10
this remark corresponds to permit ip any host 1.1.1.2
seq
10
permit ip any host 1.1.1.2
seq
15
permit ip any host 1.1.1.3
seq
20
permit ip any host 1.1.1.4
Dell# end
Dell#
resequence access-list ipv4 test 2 2
Dell# show running-config acl
!
ip access-list extended test
remark
2
XYZ
remark
4
this remark corresponds to permit any host 1.1.1.1
seq
4
permit ip any host 1.1.1.1
remark
6
this remark has no corresponding rule
Access Control Lists (ACLs)
133
Summary of Contents for S4048-ON
