manualshive.com logo in svg

Dell S4048-ON, Configuration Manual

Share
Download
Dell S4048-ON Configuration Manual Download Page 651

•

Reserved Vlan cannot have untagged ports

In the reserved

 L2 VLAN

 used for remote port mirroring:

•

MAC address learning in the reserved VLAN is automatically disabled.

•

The reserved VLAN for remote port mirroring can be automatically configured in intermediate switches by using GVRP.

•

There is no restriction on the VLAN IDs used for the reserved remote-mirroring VLAN. Valid VLAN IDs are from 2 to 4094. The 
default VLAN ID is not supported.

•

In mirrored traffic, packets that have the same destination MAC address as an intermediate or destination switch in the path 
used by the reserved VLAN to transport the mirrored traffic are dropped by the switch that receives the traffic if the switch has 
a L3 VLAN configured.

In a 

source session

 used for remote port mirroring:

•

You can configure any port as a source port in a remote-port monitoring session with a maximum of three source ports per port 

pipe.

•

Maximum number of source sessions supported on a switch: 4

•

Maximum number of source ports supported in a source session: 128

•

You can configure physical ports and port-channels as sources in remote port mirroring and use them in the same source session. 

You can use both Layer 2 (configured with the switchport command) and Layer 3 ports as source ports. You can optionally 

configure one or more source VLANs to specify the VLAN traffic to be mirrored on source ports.

•

You can use the default VLAN and native VLANs as a source VLAN.

•

You cannot configure the dedicated VLAN used to transport mirrored traffic as a source VLAN.

•

Egressing remote-vlan packets are rate limited to a default value of 100 Mbps.

In a 

destination session

 used for remote port mirroring:

•

Maximum number of destination sessions supported on a switch: 64

•

Maximum number ports supported in a destination session: 64.

•

You can configure any port as a destination port.

•

You can configure additional destination ports in an active session.

•

You can tunnel the mirrored traffic from multiple remote-port source sessions to the same destination port.

•

By default, destination port sends the mirror traffic to the probe port by stripping off the rpm header. We can also configure the 

destination port to send the mirror traffic with the rpm header intact in the original mirror traffic..

•

By default, ingress traffic on a destination port is dropped.

Restrictions

When you configure remote port mirroring, the following 

restrictions

 apply:

•

You can configure the same source port to be used in multiple source sessions.

•

You cannot configure a source port channel or source VLAN in a source session if the port channel or VLAN has a member port 

that is configured as a destination port in a remote-port mirroring session.

•

A destination port for remote port mirroring cannot be used as a source port, including the session in which the port functions as 

the destination port.

•

A destination port cannot be used in any spanning tree instance.

•

The reserved VLAN used to transport mirrored traffic must be a L2 VLAN. L3 VLANs are not supported.

•

On a source switch on which you configure source ports for remote port mirroring, you can add only one port to the dedicated 

RPM VLAN which is used to transport mirrored traffic. You can configure multiple ports for the dedicated RPM VLAN on 

intermediate and destination switches.

Displaying Remote-Port Mirroring Configurations

To display the current configuration of remote port mirroring for a specified session, enter the 

show config

 command in 

MONITOR 

SESSION

 configuration mode.

Dell(conf-mon-sess-2)#show config

!

Port Monitoring

651

Summary of Contents for S4048-ON
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands