manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 65

Dell PowerConnect B-Series TI24X Hardware Installation Guide

55

53-1002265-01

Power supply specifications

A

PDU power cords(C13-C14)

All  PowerConnect devices ship with US-compatible PDU power cords(C13- C14) unless otherwise 
specified at the time of order. United Kingdom- and European-compatible power cords are also 
available.

For PDU power cords (C13-C14) specifications, refer to 

“Input connector and plug”

 on page 57.

Power supply specifications

This section contains the following information for the power supplies that ship with PowerConnect 
B-Series TI24X devices.

•

“Overview”

•

“Key features”

•

“Physical dimensions and weight”

•

“Environmental considerations”

•

“Power supply consumption”

•

“Input connector and plug”

•

“Regulatory compliance”

•

“Safety warnings”

•

“Electrical specifications”

Overview

Each PowerConnect B-Series TI24X switch comes with one alternating-current (AC) power supplies. 
The following power supplies may be installed in your PowerConnect B-Series TI24X switch:

•

RPS-11 (8P26P) (AC power supply)

The power supplies can be swapped in or out of the device while the device is running, without 
opening the device. You can remove one of the power supplies without interrupting operation. The 
remaining power supply provides enough power for all the ports.

CAUTION

Remove the PDU power cords (C13-C14) from a power supply before you install it in or remove it 
from the device. Otherwise, the power supply or the device could be damaged. The device can be 
running while a power supply is being installed or removed, but the power supply itself should not 
be connected to a power source. 

All power supplies are auto-sensing and auto-switching.

Key features

Refer to 

“Power supplies”

 on page 6 for the key features of the PowerConnect B-Series TI24X power 

supplies.

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands