Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 56

Page: 56 / 82

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Replacing the fan tray

•

Installation precautions and warnings

•

Replacing the fan tray

Installation precautions and warnings

Follow these precautions when removing and installing a fan tray in the PowerConnect B-Series
TI24X .

CAUTION

Be careful not to accidently insert your fingers into the fan tray while removing it from the chassis.
The fan may still be spinning at a high speed.

CAUTION

Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).

CAUTION

Never leave tools inside the device.

Removing the fan tray

Use the following procedures to remove the fan tray from PowerConnect B-Series TI24X devices.

Figure 22

shows the location of the fan tray.

FIGURE 22

PowerConnect B-Series TI24X fan tray location

1. Disconnect the PDU power cords (C13-C14) from the power supply.

NOTE

If the device is connected with two Power supplies, you need to disconnect both the PDU power cords
(C13-C14) from the device.

Fan Tray

Summary of Contents for PowerConnect B-TI24x



















































































Search results

Summary of Contents for PowerConnect B-TI24x

Reviews:

Brands by name

Popular brands

Dell PowerConnect B-TI24x, Hardware Installation Manual

Search results

Summary of Contents for PowerConnect B-TI24x

Reviews:

Brands by name

Popular brands