Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 45

Page: 45 / 82

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Removing MAC address entries

To change the device poll time, enter a command such as the following at the global CONFIG level
of the CLI.

PowerConnect(config)# chassis poll-time 200

Syntax: chassis poll-time <value>

NOTE

The <value> can be 0 - 65535 seconds.

Removing MAC address entries

You can remove learned MAC address entries from the

Dell

system MAC address table. You can

remove the following entries:

•

All MAC address entries

•

All MAC address entries for a specified Ethernet port

•

All MAC address entries for a specified VLAN

•

A specified MAC address entry in all VLANs

For example, to remove entries for the MAC address 000d.cb80.00d in all VLANs, enter the
following command at the Privileged EXEC level of the CLI.

PowerConnect# clear mac-address 000d.cb80.00d0

Syntax: clear mac-address <mac-address> | ethernet <port-num> | vlan <number>

If you enter the clear mac-address command without any parameters, the software removes all
MAC entries.

Use the <mac-address> parameter to remove a specified MAC address from all VLANs. Specify the
MAC address in the following format: HHHH.HHHH.HHHH.

Use the ethernet <port-num> parameter to remove all MAC addresses for a specified Ethernet port.

Use the vlan <number> parameter to remove all MAC addresses for a specified VLAN.

Summary of Contents for PowerConnect B-TI24x



















































































Search results

Summary of Contents for PowerConnect B-TI24x

Reviews:

Brands by name

Popular brands

Dell PowerConnect B-TI24x, Hardware Installation Manual

Search results

Summary of Contents for PowerConnect B-TI24x

Reviews:

Brands by name

Popular brands