Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 4

Page: 4 / 82

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Installing the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Desktop installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rack mount installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Powering on the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Powering off the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Verifying proper operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Observing the power status LEDs. . . . . . . . . . . . . . . . . . . . . . . .20

Attaching a PC or terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Chapter 3

Connecting Network Devices and Checking Connectivity

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Assigning permanent passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Recovering from a lost password . . . . . . . . . . . . . . . . . . . . . . . . 24

Configuring IP addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Devices running Layer 2 software . . . . . . . . . . . . . . . . . . . . . . .25

Connecting network devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Connectors and cable specifications . . . . . . . . . . . . . . . . . . . . .26
Connecting to Ethernet or fast Ethernet hubs . . . . . . . . . . . . . .26
Connecting to workstations, servers, or routers . . . . . . . . . . . . 27
Connecting a network device to a fiber port . . . . . . . . . . . . . . .28

Testing connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Pinging an IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Observing LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Tracing a route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Troubleshooting network connections . . . . . . . . . . . . . . . . . . . . . . . . 31

Support for digital optical monitoring. . . . . . . . . . . . . . . . . . . . . 31

Chapter 4

Managing the PowerConnect B-Series TI24X

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Managing temperature settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Using the temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . .33
Displaying the temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Displaying temperature messages . . . . . . . . . . . . . . . . . . . . . . .34
Changing the temperature warning level . . . . . . . . . . . . . . . . . .34
Changing the device temperature polling interval. . . . . . . . . . .34

Removing MAC address entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Chapter 5

Maintaining the PowerConnect B-Series TI24X Hardware

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Hardware maintenance schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Summary of Contents for PowerConnect B-TI24x



















































































Search results

Summary of Contents for PowerConnect B-TI24x

Reviews:

Brands by name

Popular brands

Dell PowerConnect B-TI24x, Hardware Installation Manual

Search results

Summary of Contents for PowerConnect B-TI24x

Reviews:

Brands by name

Popular brands