manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 57

Dell PowerConnect B-Series TI24X Hardware Installation Guide

47

53-1002265-01

Replacing the fan tray

5

2. Loosen the two captive screws on the front plate of the fan tray and slide the tray out of the 

device as shown in 

Figure 23

.

FIGURE 23

Removing the fan tray

3. Insert the replacement fan tray, as shown in 

Figure 24

, and push it all the way into the slot to 

connect the interface.

NOTE

Ensure that the fan tray fits between the locating slides in the device.

4. Tighten the two captive screws to secure the tray in place.

FIGURE 24

Inserting a replacement fan tray

5. Connect the PDU power cords (C13-C14) to the power supply (refer to 

“Powering on the 

system”

 on page 18).

6. Verify that the system is working properly as instructed in 

“Verifying proper operation”

 on 

page 19.

1

Locating  Slide

1

1

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands